Omron JX Series Replacing Manual page 27

FI start selection 1085h
Operation frequency input A
108Eh
setting
Operation frequency input B
108Fh
setting
Operator selection 1090h
Frequency addition amount 1091h
Frequency addition direction 1093h
VR start frequency 1095h
VR end frequency 1097h
VR start ratio 1098h
VR end ratio 1099h
VR start selection 109Ah
Retry selection 10A5h
Allowable momentary power 10A6h
Retry wait time 10A7h
Momentary power
interruption/undervoltage 10A8h
trip during stop selection
Momentary power
10A9h
interruption retry time
Starting frequency at
1170h
frequency pull-in restart
Electronic thermal level 10ADh
2nd electronic thermal level 1527h
Electronic thermal
10AEh
characteristics selection
2nd electronic thermal
1528h
characteristics selection
Overload limit selection 10B5h
2nd overload limit selection 1529h
Overload limit level 10B6h
2nd overload limit level 152Ah
Overload limit parameter 10B7h
2nd overload limit parameter 152Bh
Deceleration rate constant 1171h
Frequency pull-in restart 1172h
Soft lock selection 10BCh
Selection of non-stop
function at momentary 10C9h
power interruption
Starting voltage of non-stop
function at momentary 10CAh
power interruption
Stop deceleration level of
non-stop function at
10CBh
momentary power
interruption
Deceleration time of nonstop
10CCh
function at momentary
Deceleration starting width
of non-stop function at
10CEh
momentary power
interruption
Overvoltage protection
proportional gain during 1173h
deceleration
Overvoltage protection
integral time during 1174h
deceleration
00: Start frequency A101
A105
01: 0 Hz
00: Digital Operator (F001)
01: Digital Operator (volume)
A141
02: Input FV
03: Input FI
04: RS485 communications
A142
00: Addition (A + B)
A143 01: Subtraction (A − B)
02: Multiplication (A × B)
A145 0 ～ 4000
00: Adds the A145 value to the
A146
output
A151 0 ～ 4000
A152 0 ～ 4000
A153 0 ～ 100
A154 0 ～ 100
A155 0, 1
00: Alarm
01: 0 Hz start
02: Frequency matching restart
b001
03: Trip after frequency matching
deceleration stop
b002 3 ～ 250
b003 3 ～ 1000
00: Disabled
01: Enabled
b004
00: 16 times
b005
01: No limit
00: Frequency at interruption
b011 01: Max. frequency
02: Set frequency
b012 2000 to 10000
b212 Set the rated current to 10000
b013 00: Reduced torque characteristics 1
01: Constant torque characteristics
b213 02: Reduced torque characteristics 2
b021 00: Disabled
b221 01: Enabled in acceleration/constant
b022 00: Disabled
b222 01: Enabled in acceleration/constant
b023
1 ～ 300
b223
b029 1 ～ 30000
b030 200 ～ 20000
00: Data other than b031 cannot be
changed when terminal SFT is ON.
01: Data other than b031 and the
specified frequency parameter
cannot be changed when terminal
SFT is ON.
02: Data other than b031 cannot be
b031
changed.
03: Data other than b031 and the
specified frequency parameter
cannot be changed.
10: Data other than parameters
changeable during operation cannot
be changed.
00: Disabled
b050 01: Enabled (Stop)
02: Enabled (Restart)
b051 0 ～ 10000
b052 0 ～ 10000
b053 1 ～ 30000
b054 0 ～ 100
b055 2 ～ 50
b056 0 ～ 1500
- 1287h A105
12AFh A141
-
12B0h A142
- 12B1h A143
12B3h A145(HIGH)
0.1[Hz]
12B4h A145(LOW)
- 12B5h A146
12C6h A161(HIGH)
0.1[Hz]
12C7h A161(LOW)
12C8h A162(HIGH)
0.1[Hz]
12C9h A162(LOW)
1[%] 12CAh A163
1[%] 12CBh A164
- 12CCh A165
- 1301h b001
0.1[s] 1302h b002
0.1[s] 1303h b003
- 1304h b004
- 1305h b005
- 131Fh b030
130Dh b012
0.01[%]
230Ch b212
130Eh b013
-
230Dh b213
1316h b021
-
2316h b221
1317h b022
0.01[%]
2317h b222
1318h b023
0.1[s]
2318h b223
0.1[s] 131Eh b029
0.01[%] 131Dh b028
- 1320h b031
- 1334h b050
0.1[V] 1335h b051
0.1[V] 1336h b052
1337h b053(HIGH)
0.1[s]
1338h b053(LOW)
0.1[Hz] 1339h b054
0.1 1388h b133
0.1[s] 1389h b134
27
00: FI Start Frequency (A101)
01: 0 Hz
00: Digital Operator (A020/A220)
01: Volume
02: Voltage (FV) input
03: Current (FI) input
04: Modbus communication
05: Option
07: Pulse train frequency
00: Addition (A141 + A142)
01: Subtraction (A141 − A142)
02: Multiplication (A141 × A142)
0～40000 (In the high-frequency
mode︓～58000)
00: Frequency reference + A145
01: Frequency reference − A145
0～40000 (In the high-frequency
mode︓～58000)
0～40000 (In the high-frequency
mode︓～58000)
0 to VR End Ratio
VR Start Ratio to 100
00: VR Start Frequency (A161)
01: 0 Hz
00: Trip
01: 0-Hz restart
02: Frequency matching restart
03: Trip after frequency matching
deceleration stop
04: Frequency pull-in restart
3～250
3～1000
00: Disabled
01: Enabled
02: Disabled during stop and
deceleration stop by turning off the
RUN command
00: 16 times
01: No limit
00: Frequency at interruption
01: Maximum frequency
02: Set frequency (Frequency
reference)
200～1000
00: Reduced torque characteristics
01: Constant torque characteristics
02: Free setting
00: Disabled
01: Enabled during
200～2000
1～30000
1～30000
200～2000
00: Data other than b031 cannot be
changed when terminal SFT is ON.
01: Data other than b031 and the
set frequency cannot be changed
when terminal SFT is ON.
02: Data other than b031 cannot be
changed.
03: Data other than b031 and set
frequency cannot be changed.
10: Data can be changed during
RUN.
00: Disabled
01: Enabled (Deceleration stop)
02: Enabled (Constant voltage,
without recovery)
03: Enabled (Constant voltage, with
recovery)
0～10000
0～10000
1～360000
0～1000 (In the high-frequency
mode︓10000)
0～500
0～1500
-
-
-
0.01[Hz]
-
0.01[Hz]
0.01[Hz]
1[%]
1[%]
-
-
0.1[s]
0.1[s]
-
-
-
0.1[%]
-
-
0.1[%]
0.1[s]
0.1[s]
0.1[%]
-
-
0.1[V]
0.1[V]
0.01[s]
0.01[Hz]
0.01
0.1[s]