Tape Remaining Time - JVC HR-DVS2EU Instructions Manual

Retake (VHS Deck Only)
You can cut out unnecessary parts of a TV programme while
you're recording it.
End of programme
Unnecessary
Programme
part
Recorded part
Go back to end of programme to cut out
unnecessary part
ENGAGE RECORD-PAUSE
MODE
1
Press PAUSE during recording.
LOCATE START POINT
2
Turn the JOG dial to the left or right (or hold down REW
or FF) and release it when you reach the point where
you want to resume recording.
* Your recorder returns to the Record-Pause mode.
RESUME RECORDING
3
Press PLAY when you wish to resume recording.
NOTES:
Retake function does not work during Direct Rec (
Noise may appear when Retake function is used at the part
that is recorded in EP mode.

Tape Remaining Time

(VHS Deck Only)
DISPLAY REMAINING TIME
1
Press – –:– – until the time remaining on the tape
appears.
The display panel shows the tape remaining time
with " " displayed.
By pressing the – –:– – button, you can change the
display to show the counter reading (VHS deck only),
time code (DV deck only), channel position*, clock
time or tape remaining time (VHS deck only).
* channel position is not displayed during playback.
NOTE:
Depending on the type of tape used, there may be times when
the tape remaining time reading may not appear right away, or
is not correct. "– –:– –" may sometimes appear, or the display
may blink on occasion.
Beginning of programme
Unnecessary
Programme
part
pg. 16).
Super VHS (S-VHS),
Super VHS ET (S-VHS ET)
and VHS (VHS Deck Only)
Your recorder can record in S-VHS (Super VHS), S-VHS ET or
VHS.
To record in S-VHS:
Perform the steps 1 – 4 below to set "S-VHS" to "ON".
Then, insert a cassette marked "S-VHS". The S-VHS indicator
lights up on the front display panel.
The S-VHS recording mode is selected.
To record in S-VHS ET on a VHS cassette:
See "Super VHS ET (S-VHS ET)" on page 30.
To record in VHS:
Insert a cassette marked "VHS".
Press S-VHS ET on the recorder. You can check the current
setting ("S-VHS ET : ON" or "S-VHS ET : OFF") if "O.S.D." is set
to "ON" ( pg. 11). If "S-VHS ET : ON" appears on the TV
screen, press S-VHS ET again in about 5 seconds to set it to
"OFF".
The VHS recording mode is automatically selected regardless of
the "S-VHS" mode setting.
To record in VHS on an S-VHS cassette:
Insert the cassette marked "S-VHS". The S-VHS indicator will
light on the display panel.
Then, perform the steps 1 – 4 below to set the "S-VHS" to "OFF".
The S-VHS indicator goes off.
The VHS recording mode will be selected.
ACCESS MAIN MENU
SCREEN
1
Press MENU.
ACCESS VHS MODE SET
SCREEN
2
Move the highlight bar (pointer) to "VHS MODE SET" by
pressing %fi, then press OK or
SELECT S-VHS MODE
3
Move the highlight
(pointer) to "S-VHS" by
pressing %fi, then press
#
OK or to select "ON" or
"OFF".
RETURN TO NORMAL
SCREEN
4
Press MENU.
NOTE:
When playing back a tape that has been recorded in S-VHS, the
S-VHS indicator lights on the display panel regardless of the
"S-VHS" mode setting.
29
EN
#
.
VHS MODE SET
B. E. S. T. ON
PICTURE CONTROL AUTO
AUTO SP=LP TIMER OFF
DIGITAL 3R ON
S-VHS ON
COLOUR SYSTEM PAL/NTSC
DIGITAL TBC/NR ON
VIDEO STABILIZER OFF
[5∞] =
[MENU] : EXIT