Other Handy Functions - Clarion XDZ716 Owner's Manual

Other Handy Functions

Entering titles
Titles up to 10 characters long can be stored in
memory and displayed for TV stations. The num-
bers of titles that can be entered for each mode
are as follows.
Mode Number of titles
TV mode 15 titles
CD changer mode Number of titles
CDC655z connected 60 titles
CDC655Tz connected 100 titles
CDC1255z connected 50 titles
1. Press FNC button 3 to select the mode you
want to enter a title (CD changer or TV).
2. Select and play a CD in the CD changer or
tune in to a TV station for which you want to
enter the title.
3. Press DISP button # and display the main.
4. Press TITLE button 2. "TTL" appears in the
display and the cursor position flashes.
5. Press the right or left side of SEARCH button
% to move the cursor.
6. Press DISP button # to select a character.
Each time you press DISP button #, the char-
acter changes in the following order:
Capital letters Small letters Numbers and
Symbols Umlaut Capital letters...
7. Turn the Rotary knob ( to select the desired
character. Turning the Rotary knob ( clock-
wise moves the cursor to the next character;
turning it counterclockwise moves the cursor
to the previous character.
8. Repeat steps 5 to 7 to enter up to 10 charac-
ters for the title.
9. Press and hold ENT button & for 2 seconds
or longer to store the title into memory and
cancel title input mode.
Clearing titles
1. Select and play a CD in the CD changer or
tune in to a TV station for which you want to
clear the title.
2. Press DISP button # and display the main.
3. Press TITLE button 2. "TTL" appears in the dis-
play and the display switches to title input display.
4. Press BND button ".
5. Press and hold ENT button & for 2 seconds or
longer to clear the title and cancel title input mode.
16
XDZ716
Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
The factory default setting is "8". (Adjustment level:
1 to 18)
1. Press and hold ADJ button 2 for 1 second or
longer to switch to the adjustment selection display.
2. Press the right or left side of SEARCH button
% to select "CONTRAST".
3. Turn the Rotary knob ( clockwise or coun-
terclockwise to adjust the contrast.
4. Press ADJ button 2 to return to the previous
mode.
Adjusting the dimmer level
You can adjust the reduced illumination level of
the dimmer.
The factory default setting is "3".
To use the dimmer, set the dimmer setting to 1 to 5.
1. Press and hold ADJ button 2 for 1 second or longer
to switch to the adjustment selection display.
2. Press the right or left side of SEARCH button
% to select "DIMMER LV".
3. Turn the Rotary knob ( clockwise or coun-
terclockwise to adjust the reduced illumina-
tion level of the dimmer.
1 to 5:
The dimmer operation is performed depend-
ing on the set level 1 to 5.
OFF:
No dimmer operation is performed.
4. Press ADJ button 2 to return to the previous mode.
Message display
When the unit is powered on or off, a message is
displayed. The user can turn this message dis-
play ON or OFF.
The factory default setting is "ON".
1. Press and hold ADJ button 2 for 1 second or
longer to switch to the adjustment selection display.
2. Press the right or left side of SEARCH button
% to select "MESSAGE".
3. Turn the Rotary knob ( clockwise or counter-
clockwise to set message display ON or OFF.
4. Press ADJ button 2 to return to the previous mode.
Turning the external output
adjustment display on/off
When not using the external output, you can put
out the "NON-FADER" display.
The factory default setting is "ON".
Even if the level adjustment display is set to "OFF",
signals can be output from the external output.
1. Press and hold ADJ button 2 for 1 second or
longer to switch to the adjustment selection display.
2. Press the right or left side of SEARCH button
% to select "NON-FADER".
3. Turn the Rotary knob ( clockwise to set "ON"
or counterclockwise to set "OFF".
ON:
When you press A-M button $, the "NON-
FAD VOL" item is displayed.
The output level can be adjusted.
OFF:
Even when you press A-M button $, the
"NON-FAD VOL" item is not displayed.
The output level cannot be adjusted.
4. Press ADJ button 2 to return to the previous
mode.
AUX function
This system has an external input jack so you
can listen to sounds and music from external
devices when connected to this unit.
Selecting AUX IN sensitivity
Make the following settings to select the sensi-
tivity when sounds from external devices con-
nected to this unit are difficult to hear even after
adjusting the volume.
1. Press and hold the ADJ button 2 for 1 second
or longer to set Adjust mode.
2. Press the SEARCH button % and select "AUX
SENS".
3. Turn the Rotary knob ( clockwise or coun-
terclockwise as needed and select from
"SENS HIGH", "SENS MID" or "SENS LOW".
The factory default setting is "SENS MID".
4. Press ADJ button 2 to return the previous mode.
Setting the button illumination
The factory default setting is "ILLM GREEN".
1. Press and hold the ADJ button 2 for 1 sec-
ond or longer to set Adjust mode.
2. Press the SEARCH button % and select "KEY
ILLUMI".
3. Turn the Rotary knob ( clockwise or coun-
terclockwise as needed and select from "ILLM
GREEN" and "ILLM RED".
4. Press ADJ button 2 to return the previous
mode.
Other Handy Functions
Setting the method for Ttitle scroll
Set how to scroll in CD-TEXT or MD.
The factory default setting is "ON".
1. Press and hold the ADJ button 2 for 1 sec-
ond or longer to set Adjust mode.
2. Press the SEARCH button % and select
"AUTO SCROLL".
3. Turn the Rotary knob ( clockwise or coun-
terclockwise and select "ON" or "OFF".
ON:
To scroll automatically.
OFF:
To scroll just 1 time when the title was changed
or the title key was pressed.
4. Press ADJ button 2 to return the previous mode.
Switching the screen saver
The factory default setting is "RANDOM".
1. Press and hold the ADJ button 2 for 1 sec-
ond or longer to set Adjust mode.
2. Press the SEARCH button % and select
"AUTO SS".
3. Turn the Rotary knob ( clockwise or coun-
terclockwise as needed to switch to "SS OFF"
"SS Ptn1" "SS Ptn2" "SS Ptn3" "SS
RANDOM" "SS OFF"
4. Press ADJ button 2 to return the previous
mode.
Setteng the clock
1. Press and hold the ADJ button 2 for 1 sec-
ond or longer to set Adjust mode.
2. Press the SEARCH button % and select
"CLOCK".
3. Press ENT button & .
4. Press the SEARCH button % to select the
hour or the minute.
5. Turn the Rotaly knob ( clockwise or
counterclockwise to set the correct time.
The clock is displayed in 12-hour format.
6. Press ENT button & to store the time into
memory.
7. Press ADJ button 2 to return the previous
mode.
Note:
• You cannot set the clock when it is displayed with
only the ignition on.If you drain or remove the car's
battery or take out this unit, the clock is reset. While
setting the clock, if another button or operation is
selected, the clock set mode is canceled.
17
XDZ716