Sony BVP-E10 Series Product Information Manual page 89

the connector that corresponds to the lit
button. The output signal from the other
connector does not change. By lighting both
the buttons, you can simultaneously select the
output signal.
Note
If you light both the WF and PIX buttons when
different signals are selected for the WF2
OUTPUT and PIX2 OUTPUT connectors, the
output select buttons corresponding to the
k Camera select block
1
PANEL PARA EXPAND
ACTIVE
0 7
0 1
A PANEL ACTIVE button
Press and light up this button to permit the
cameras selected with the camera select
buttons to be controlled from this unit. The IRIS/
MB ACTIVE button also lights up. If you press
the button when lit, it goes dark and the
operation panel of this unit is locked.
B PARA (parallel mode) button
Press and light up this button to activate Parallel
mode, which enables concurrent operation with
another control panel. If you press the button
when lit, it goes dark and the Parallel mode is
canceled.
C EXPAND button
Press to select the group to be selected with the
camera select buttons. Cameras 1 through 12
can be selected when this button is not lit, and
cameras 13 through 24 can be selected when
this button is lit.
Note
An appropriate camera command network unit
(CNU- 700, etc.) is required to control multiple
cameras using the camera select function.
D MULTI indicators
Show the Master/Slave status of the
corresponding cameras 1 through 12 (when the
EXPAND button is not lit) or 13 through 24 (when
the EXPAND button is lit).
The indicator for the camera that is specified as
the master for Master/Slave mode lights green.
The indicators for the slave cameras light
orange. They light red during the auto setup of
the corresponding cameras. If an error occurs
during the auto setup and the operation is
interrupted, they will flash red.
2 3
0 8 0 9 1 0 1 1
0 2 0 3 0 4 0 5
E TALLY indicators
F Active indicators
G Camera select buttons and camera number
signals selected for either of the connectors
flash. Press the button for the signal to be output
to select it again.
For example, when you light both the WF and
PIX buttons with R + B selected for PIX2
OUTPUT and B + G selected for WF2 OUTPUT,
the R and G buttons will start flashing, while the
B button will remain lit. To output R and G, press
the R and G buttons. Each pressed button stops
flashing and illuminates.
4
MULTI
TALLY
5
6
1 2
7
4
MULTI
TALLY
5
6
0 6
7
Show the tally status of the corresponding
cameras 1 through 12 (when the EXPAND
button is not lit) or 13 through 24 (when the
EXPAND button is lit). The corresponding
indicator lights red when a red tally is sent to a
camera, and it lights green when a green tally is
sent. When both red and green tally are sent, it
lights orange. When a call signal is sent to the
camera, the indicator rapidly flashes red.
Show the control status of the corresponding
cameras 1 through 12 (when the EXPAND
button is not lit) or 13 through 24 (when the
EXPAND button is lit). The indicators for the
cameras under control of this unit light green
and the indicators for the cameras under control
of another control panel light orange.
An indicator whose corresponding camera (or
camera control unit) is not connected does not
light.
An indicator lights red when an error is detected
and the self-diagnostic functions are activated
in the corresponding camera or camera control
unit.
indicators
Select the cameras to be controlled from this
unit. Press and light up the button
corresponding to each desired camera. When
the EXPAND button is not lit, numbers 1 through
12 are displayed and cameras 1 through 12 are
selected. When the EXPAND button is lit,
numbers 13 through 24 are displayed and
cameras 13 through 24 are selected.
Chapter 7 Location and Function of Parts and Controls
BVP-E10 Series Product Information Manual
89