Sony BVP-E10 Series Product Information Manual page 88

7
Chapter 7 Location and Function of Parts and Controls
88
BVP-E10 Series Product Information Manual
during this time, the video camera returns to the state
before the button was lit.
g AUTO SETUP block g g g
For automatic adjustments of cameras.
1 2
AUTO SETUP
AUTO LEVEL START/
WHITE BLACK
HUE
BREAK
A Auto adjustment item select buttons
Press and light up these buttons to select the
items to be automatically adjusted.
AUTO HUE: Skin tone detail automatic hue
LEVEL: Gamma balance, knee point, master
black level, etc.
B START/BREAK button
Press to start automatic adjustment of the
selected items. The button lights during
adjustment and goes dark when adjustment is
completed. If you press the button when lit, the
automatic adjustment is canceled and the
button flashes. To stop the flashing, press the
button again.
C WHITE (white balance) button
Press to automatically adjust the white balance.
The button lights during adjustment and goes
dark when adjustment is completed. If you press
this button when lit or the START/ BREAK button,
the automatic adjustment is canceled and the
button flashes. To stop the flashing, press the
button again.
D BLACK (black balance) button
Press to automatically adjust the black balance
and black set. The button lights during
adjustment and goes dark when adjustment is
completed. If you press this button when lit or
the START/ BREAK button, the automatic
adjustment is canceled and the button flashes.
To stop the flashing, press the button again.
Note
If an error occurs during adjustment, the
pressed button flashes.
h h Camera/CCU function ON/OFF buttons h h
Various functions of the video camera or the CCU can
be turned on and off from this unit (ON when the button
is lit).
The following switching functions are assigned to four
of the buttons at the factory and the other three buttons
are reserved for future use.
5600K AUTO SKIN
KNEE DETAIL
5600K: 5600K -electronic colour temperature
conversion function
AUTO KNEE: Auto knee function. When this button
is lit (ON), the knee point is automatically adjusted
according to the light content of the picture.
SKIN DETAIL: Skin tone detail function
CHARACTER: System information display
function. Various information relating to the entire
system is displayed on the monitor connected to
the CHARACTER connector of the CNU-700. The
display contents can be changed through a menu
operation.
i Scene file control block i
i i
1 SCENE FILES button
3 4
1
A SCENE FILES buttons
When the STORE button is dark: The stored
data can be retrieved by pressing and lighting
up the button of the desired number. Press the
lit button to turn it dark and resume the previous
status.
While the STORE button is flashing: When
you press one of these buttons, the current
setting data is stored as a file of the
corresponding number.
B STORE button
To store a scene file, first press this button so
that the button starts flashing, then press the
SCENE FILES button of the desired number.
When file registration is completed, the STORE
button goes dark. To cancel the registration,
press the flashing button again before pressing
the SCENE FILES button. The STORE button
goes dark.
j Monitor output select buttons j j j
Press to select the output signal from the WF2 and
PIX2 OUTPUT connectors of CCU-700A/AP or PIX
OUTPUT connector of CCU-550D/550DP.
R
A Output signal select buttons
After selecting the output connector of the CCU
by pressing either the WF or PIX button, press to
light the button for the signal to be output. The
signal corresponding to the lit button is output.
R/G/B: Select the R signal, G signal, or B signal.
SEQ (sequence): Effective only for the WF2
ENC (encode): When this button is pressed, the
CHARACTER
B Output connector select buttons
WF: Press to light the button when switching the
PIX: Press and light the button when switching
2 STORE button
2 3 4 5
SCENE FILES
1
G B
SEQ ENC
MONITOR
The signals can be selected either
independently or in combination. When any of
these buttons is pressed, the SEQ (for WF
only) and ENC circuits are turned off.
OUTPUT connector. When this button is
pressed, the R/G/B circuits are turned off, and
the SEQ signal is output. You can monitor the
waveforms of the three R, G, and B signals in
sequence on a waveform monitor.
R/G/B and SEQ circuits are turned off, and the
ENC signal is output.
output signal from the WF2 OUTPUT
connector with the output signal select
buttons. Press the button again to make it go
dark.
the output signal from the PIX2 OUTPUT
connector with the output signal select
buttons. Press the button again to make it go
dark.
When one of these buttons is lit, pressing the
output signal select buttons has effect only on
STORE
2
WF PIX