Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel MINIMAL
Summary of Contents for Fisher & Paykel MINIMAL
- Page 1 DOWNDRAFT INDUCTION COOKTOP MINIMAL CID834RDTB4 INSTALLATION GUIDE UK IE...
- Page 3 SAFETY AND WARNINGS READ AND SAVE THIS GUIDE WARNING! General Use Electric Shock Hazard Read these instructions carefully before installing this product. Failure to follow this advice may result in Save these instructions for the local electrical inspector’s use. Installation must comply with your local building and local electricity regulations. electric shock or death.
-
Page 4: Installation Considerations
INSTALLATION CONSIDERATIONS BEFORE INSTALLATION DURING INSTALLATION Please ensure the following: Please ensure the following: A suitable disconnection switch is incorporated in the permanent wiring, mounted and Flush mounting or sealing this appliance into the bench with silicone or glue may make positioned to comply with the local wiring rules and regulations. -
Page 5: Tools And Components
TOOLS AND COMPONENTS PARTS SUPPLIED COMPONENTS REQUIRED Keep all packing materials until the unit has been inspected. Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher &... -
Page 6: Product Dimensions
PRODUCT DIMENSIONS PRODUCT DIMENSIONS A Overall height of cooktop B Overall width of cooktop C Overall depth of cooktop* D Depth of cooktop surface E Height of chassis F Width of chassis G Depth of chassis H Depth of front overhang of cooktop glass** I Depth of rear overhang of cooktop glass** J Depth of left overhang of cooktop glass** PLAN... -
Page 7: Accessory Dimensions
ACCESSORY DIMENSIONS HORIZONTAL ELBOW DUCTING ACCESSORY DIMENSIONS A Overall height of horizontal elbow B Overall width of horizontal elbow C Overall depth of horizontal elbow D Overall height of ducting E Overall width of ducting F Overall depth of ducting 1000 G Overall height of connector H Overall width of connector... -
Page 8: Flush Installation
CUTOUT PROUD INSTALLATION FLUSH INSTALLATION PLAN PLAN FRONT FRONT CUTOUT DIMENSIONS CUTOUT DIMENSIONS A Overall height of routered recess* B Overall width of routered recess A Overall width of cutout C Overall depth of routered recess B Overall depth of cutout D Overall width of cutout C Minimum depth at rear E Overall depth of cutout... -
Page 9: Clearance Dimensions
CLEARANCES CLEARANCE DIMENSIONS A Minimum clearance from cook surface to: Unprotected overhead cabinet centered above cooktop*† Protected overhead cabinet centered above cooktop*† B Minimum clearance below countertop** C Minimum clearance from side of cutout to nearest adjacent combustible surface D Maximum depth of combustible overhead cabinetry E Minimum distance between overhead cabinets (centred above cooktop) - Page 10 VENTING PREPARATION VENTING TO THE FRONT A toe kick height of at least 60mm is required. Front facing venting is achievable in both island and wall installations providing adequate airflow is present at the outlet location. Venting to the front through the same cabinet can be achieved using the supplied ducting components.
- Page 11 ELECTRICAL CONNECTION CONNECTION LOCATION SINGLE-PHASE CONNECTION Before connecting the cooktop to the mains power supply check that: 220-240V~ Ensure cable is tightened with screw. The domestic wiring system is suitable for the power drawn by the cooktop. You may have to remove the screw The voltage corresponds to the value given in the rating plate.
- Page 12 INSTALL DUCTING 334mm Prepare the toe kick panel to the illustrated specifications. Fit the outlet to the ducting and 13mm 34mm We recommend sealing the panel 60mm – tape to secure. 200mm with a waterproof barrier to prevent any moisture damage. max panel thickness: 16mm Align the outlet to the toe kick panel and adjust the height...
- Page 13 INSTALL COOKTOP – PROUD Optional 62mm extender block Slot the two filter housing components together. If using the supplied 62mm extension blocks*, Turn the cooktop upside down add between the two filter on a protective cover. housing components as required. Fit to the rear of the cooktop.
- Page 14 INSTALL COOKTOP – FLUSH Filter housing Ducting Prepare the countertop for flush Align vertical ducting to the installation. Use a router to cutout outlet to the cooktop before the edges of the countertop to rotating and lowering it into specified depth (6mm). Ensure all the cutout.
-
Page 15: Installer Checklist
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER GENERAL VENTILATION … … Read safety and warnings in the user guide before operating the cooktop. Ensure all ducting components are taped securely. … … Specified clearance maintained. Check outlets are clear and not obstructed. …... - Page 16 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2021. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.