Advertisement
E5@N/E5@N-H
Protect Level
The time taken to move to the protect level
can be adjusted by changing the "Move to
protect level time" setting.
pmov
Move to Protect Level:
Displayed only when a password
0
is set. Restricts moving to protect
level.
M
Operation/Adjustment
Protect:
oapt
Restricts displaying and
modifying menus in
0
operation, adjustment, and
M
manual control levels.
Initial Setting/
icpt
Communications Protect:
This protect level restricts
0
movement to the initial setting,
communications setting, and
M
advanced function setting levels.
wtpt
Setting Change Protect:
Protects changes to setups
off
by operating the front panel
keys.
M
pfpt
PF Key Protect
Restricts PF key operation
off
(E5AN-H/E5EN-H only)
M
pmsk
Parameter Mask Enable:
Displayed only when a
on
parameter mask is set.
M
prlp
Password to Move to
Protect Level:
0
Password setting
M
64
Press the O Key for at least 1 s.
Press the O Key for at least 3 s.
Other than the Auto/Manual Switch display
Press the O Key less than 1 s.
Communications
Setting Level
Displayed only for models with communications. Changes
are effective after cycling power or after a software reset.
Protocol Setting:
psel
Switches between
CompoWay/F (SYSWAY)
cwf
and Modbus.
M
u-no
Communications Unit No.
1
M
bps
Communications
Baud Rate
9.6
CompoWay/F
(SYSWAY) only
M
len
Communications
Data Length
7
M
sbit
Communications
Stop Bits
2
M
prty
Communications Parity
even
M
sdwt
Send Data Wait Time
20
M
Initial Setting Level
Press the O Key less than 1 s.
in-t
Input Type
alt2
5
M
in-h
Scaling Upper Limit
alh2
100
c
M
in-l
Scaling Lower Limit
0
alt3
M
dp
Decimal Point
0
alh3
c
For input type of analog
M
d-u
Temperature Unit
°C, °F
c
For input type of
tr-t
temperature
M
sl-h
SP Upper Limit
c
1300.0
tr-h
M
Limit the set point
sl-l
c
SP Lower Limit
-200.0
tr-l
M
cntl
PID ON/OFF
o1-t
pid
M
s-hc
Standard or
Heating/Cooling
ev-b
stnd
M
st
ST (Self-tuning)
For input type of
on
ev-1
temperature,
M
standard control, or
PID
ptrn
Program Pattern
off
ev-2
M
pbnk
Valid Program Bank
7
When assigning PID or
ev-3
control output to ON/OFF
M
output
cp
Control Period (Heating)
20
ev-4
M
Set the ON/OFF
output cycle.
c-cp
Control Period (Cooling)
20
clfl
M
orev
Direct/Reverse Operation
or-r
calb
M
alt1
Alarm 1 Type
2
M
alh1
c
Alarm 1
Hysteresis
0.2
M
amov
Alarm 2 Type
2
M
Alarm 2
Hysteresis
0.2
M
Alarm 3 Type
2
M
Alarm 3
Hysteresis
0.2
M
Transfer Output Type
off
Linear output
M
Transfer Output
Upper Limit
100.0
M
Transfer Output
Lower Limit
0.0
M
Linear Current Output
4-20
Linear output
M
Bank Numbers Used
1
M
Event Input
Assignment 1
none
M
Event Input
Assignment 2
stop
M
Event Input
Assignment 3
none
M
Event Input
Assignment 4
none
M
Closed/Floating
flot
M
Motor Calibration
off
M
mot
Travel Time
30
M
sqr
Extraction of Square
Root Enable
off
M
Move to Advanced Function
Setting Level:
Displayed when initial
0
setting/ communications
protect is set to 0.
M
Move by setting password (−169).
Advertisement
