Table of Contents
Advertisement
Connects the intercom headset.
To use a headset with a plug other than an XLR 5-pin plug,
consult a Sony service or sales representative.
f Optical signal reception status indicator
When the two lamps on the right (green) are lighted:
Reception status is excellent.
When the second lamp from the right (green) is lighted:
Reception status is good.
When the second lamp from the left (yellow) is lighted:
Reception status is low.
When the lamp on the left (red) is lighted: Reception status
is at the lowest level.
g Status display indicator
REF IN (Green): REFERENCE is being input.
UNLOCK (Red): The input REFERENCE is not locked.
COM ERROR (Red): There is a communication failure with
the camera or other external control equipment (such as
the RCP-1000 series Remote Control Panel).
FAN STOP (Red): The power fan is stopped.
h MENU control block
DISP/MENU (display/menu) lever and indicator
CANCEL/ENTER lever
CONTROL knob
• DISP/MENU (display/menu) lever and indicator
Selects the status display or setup menu display. In setup
menu mode, the indicator turns on.
• CANCEL/ENTER lever
In setup menu mode, used to cancel and enter settings.
• CONTROL knob (rotary encoder)
In status screen mode, used to change the displayed page. In
setup menu mode, used to move the cursor on a page and to
change menu settings.
Pressing the CONTROL knob performs the same function as
setting the CANCEL/ENTER lever to the ENTER position.
i CABLE ALARM indicators
SHORT (red): Lights in red when the power supply cord of an
optical fiber cable is short to external, or two power
supply cords are short. Power isn't input to the camera
when this indicator lights.
OPEN (red): Lights in red when a camera isn't connected to
the CAMERA connector on the rear panel of this unit via
an optical fiber cable. Flashes when the connection
status of an optical fiber cable is bad.
j MAIN POWER switch and indicator
Turns the entire camera system on and off, including this unit,
the video camera, and the RCP-1000 series Remote Control
Panel connected to the REMOTE connector of this unit.
Press the "?" side to turn the camera system on, and the "a"
side to turn it off. The indicator lights when the power switch is
turned on.
k CAMERA POWER switch and indicator
Turns the video camera on and off when the MAIN POWER
switch is turned on. Press the top side to turn on the video
camera and the bottom side to turn it off.
When the CAM PW button of the remote control panel
connected to this unit is set to off, this switch alone cannot be
used to turn on the video camera.
l Call button
When pressed, this outputs a call signal to the camera and
external control device (the RCP-1000 series, etc.) that are
connected to this unit. Use this when you want to call and
speak with the camera operator or external control device
operator via intercom.
m Assignable button
You can set a function for this button via the CCU menu.
n Network indicator
Displays the network system connection status.
On: When CNS SETTING in the NETWORK SETTING menu
is set to either BRIDGE or MCS, this indicates that
external control equipment (MSU-1000/1500 Master
Setup Unit, RCP-1000-series Remote Control Panel, or
other device) is connected.
Flashing: When CNS SETTING in the NETWORK SETTING
menu is set to either BRIDGE or MCS, this indicates a
connection problem with the external control equipment
(MSU-1000/1500 Master Setup Unit, RCP-1000-series
Remote Control Panel, or other device).
Off: When CNS SETTING in the NETWORK SETTING menu
is set to either BRIDGE or MCS, this indicates that a LAN
cable is not connected or that the network system
connection parameters have not been set.
When the CNS SETTING in the NETWORK SETTING
menu is set to LEGACY, this remains turned off.
o Menu lock switch
This locks out operation of the front panel menu operation
area.
8
Advertisement
Table of Contents
