Table of Contents
Advertisement
SYSTEM OPERATION
Page name
Item
Page No.
<MULTI FORMAT>
FREQUENCY
S03
Note
CAMERA FORMAT
• FREQUENCY or
CAMERA FORMAT
mode setting changes
take effect only after the
CCU power supply is
turned off and then on
again.
• Notes when changing
FORMAT
When BPU is attached,
confirm if the FORMAT
of BPU is set correctly
after changing the
FORMAT of CCU.
Also, when you change
the FORMAT of BPU,
FRAME CONVERT
change the FORMAT of
DELAY
CCU beforehand.
CCU VIDEO
CONVERT
2× MODE
BIT DEPTH
3G-SDI
HD-SD DELAY
COMPONENT
Settings
HD
1.001, 1.000
SD
(525NTSC), (625PAL)
When FREQUENCY is set to
1.001: 1080/59.94I, 1080/
29.97PsF, 1080/59.94P, 1080/
23.98PsF, 720/59.94P, 1080/
59.94I (RGB444), 1080/
29.97PsF (RGB444), 1080/
23.98PsF (RGB444), 1080/59I (2×),
720/59P (2×), 1080/59.94P (4K/
HDR)
When FREQUENCY is set to
1.000: 1080/50I, 1080/25PsF,
1080/50P, 1080/24PsF, 720/50P,
1080/50I (RGB444), 1080/25PsF
(RGB444), 1080/24PsF (RGB444),
1080/50I (2×), 720/50P (2×), 1080/
50P (4K/HDR)
0.8, 1.2, 1.6
DSB, ENB
0, 1, 2
10bit, 12bit
Level A, Level B
Line (90H), Frame (1F), 0-Delay
RGB, YCD
Description
Selects the operating frequency.
Selects the transmission format.
Sets the output delay for framerate-converted
signals. (Displayed only when FREQUENCY HD is
set to 1.001.)
Sets video conversion. When CAMERA FORMAT is
set to 1080/59.94P or 1080/50P, set to ENB to
convert/output 720/59.94P or 720/50P signal from
the DRX board. To set to ENB, set FRAME
SYNCHRO in RETURN SETUP (S07) to ON.
Tip: When CCU VIDEO CONVERT is set to ENB,
the CCU internal video conversion is delayed, so
adjust the camera's signal by advancing it as
necessary.
Sets the output format to 2× frame output. The CCU
output format changes.
0: Compatible with SR-R1000.
1: Compatible with servers manufactured by EVS.
2: Compatible with SRW-1/5800.
Displayed only when CAMERA FORMAT is set to
1080/59.94I (2×), 1080/50I (2×), 720/59.94P (2×) or
720/50P (2×).
Sets the output bit length to RGB 4:4:4.
The CCU output format changes.
Displayed only when CAMERA FORMAT is set to
1080/59.94I (RGB444), 1080/29.97PsF (RGB444),
1080/23.98PsF (RGB444), 1080/50I (RGB444),
1080/25PsF (RGB444) or 1080/24PsF (RGB444).
Selects SMPTE425 Level A or SMPTE425 Level B
for 3G-SDI output.
Sets the phase output for SD signals down
converted from this unit's HD signals.
Selects the component signal connector's output
format.
(Displayed only when HKCU1003 is installed.)
38
Advertisement
Table of Contents
