Panasonic AW-UE100WP Operating Instructions Manual page 134

Web screen configurations (continued)
Fall S-Curve [0 to 30]
Sets the S-curve for pan/tilt deceleration operation in 31 steps. (The S
becomes stronger, the greater the number)
During the fall acceleration operation for operating at the specified
speed or time during pan/tilt operations by preset playback, the
deceleration process is performed using the S-curve specified in this
setting.
This is enabled only when [Preset Acceleration] is [Manual].
Factory settings: 15
<NOTE>
• In order to limit the deceleration response, in the S-curve step, as
the deceleration speed rises, the limit is automatically applied.
Rise Acceleration [1 to 255]
Sets the acceleration speed for pan/tilt acceleration operation in 255
steps. (The acceleration speed increases as the number increases)
During the acceleration operation for operating at the specified speed
or time during pan/tilt operations by preset playback, the acceleration
process is performed using the acceleration speed specified in this
setting.
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Speed Table].
Factory settings: 128
<NOTE>
• As the speed specified for [Preset Speed] is given priority as the
maximum speed attained in preset playback, if the acceleration
speed specified here is small, this functionality may not operate as
specified.
Fall Acceleration [1 to 255]
Sets the deceleration speed for pan/tilt deceleration operation in 255
steps. (The deceleration speed increases as the number increases)
During the deceleration operation for operating at the specified speed
or time during pan/tilt operations by preset playback, the deceleration
process is performed using the deceleration speed specified in this
setting.
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Speed Table].
Factory settings: 128
<NOTE>
• As the speed specified for [Preset Speed] is given priority as the
maximum speed attained in preset playback, if the deceleration
speed specified here is small, this functionality may not operate as
specified.
Rise Ramp Time [0.1s to 10.0s]
Sets the acceleration time for the time specific operation during preset
playback. (Sets between 0.1 s to 10.0 s in 0.1s increments)
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Time].
Factory settings: 0.1s
<NOTE>
• As the time specified in [Preset Speed] takes precedence as the
total time for preset playback, if the time specified here is more than
half of the time specified in [Preset Speed], this functionality will not
operate as specified.
• When the acceleration operation cannot be performed within the
specified time even at maximum acceleration speed of the device,
the operation will not be performed by the specified time.
Fall Ramp Time [0.1s to 10.0s]
Sets the deceleration time for time specified operations during preset
playback. (Sets between 0.1 s to 10.0 s in 0.1s increments)
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Time].
Factory settings: 0.1s
<NOTE>
• As the time specified in [Preset Speed] takes precedence as the
total time for preset playback, if the time specified here is more than
half of the time specified in [Preset Speed], this functionality will not
operate as specified.
• When the deceleration operation cannot be performed within the
specified time even at maximum fall deceleration of the device, the
operation will not be performed by the specified time.
Preset Scope [Mode A, Mode B, Mode C]
Selected here are the setting items to be recalled when the contents
of the preset memory are regenerated.
Pan, Tilt, Zoom (including digital zoom), Focus, Iris, Gain,
Mode A
white balance adjustment value
Mode B Pan, Tilt, Zoom (including digital zoom), Focus, Iris
Mode C Pan, Tilt, Zoom (including digital zoom), Focus
Factory settings: Mode A
Preset Digital Extender [Off, On]
Turns the preset digital extender function off/on.
When set to [On], the digital extender function configuration will be
recalled when regenerating the preset memory.
When set to [Off], the digital extender function configuration will not
be recalled when storing the preset memory.
Factory settings: Off
134