3000 series professional uhf wireless systems unipak transmitter system handheld dynamic microphone system handheld condenser microphone system (21 pages)
Introduction Thank you for purchasing this Audio-Technica product. Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future reference. Important information Warning: For customers in the USA •...
Notes on use • Be sure to read the user manual for any microphone or cable that you attach to the product. • Disconnect the AC adapter from the outlet when this product is not in use. • Turn off the power of this product before connecting or disconnecting cables. •...
Part names and functions ATW-R3210 Front panel ❶ ❷ ❸ ❹ ❺ ❶ Power button ( Use to turn the receiver on or off. ❷ IR sync window Use to IR SYNC with the transmitter (ATW-T3201, ATW-T3202). ❸ Display Displays the receiver state and setting menus.
Page 6
Part names and functions Rear panel ❻ ❶ ❷ ❸ ❹ ❺ ❶ Antenna input jack Each jack supplies DC12 V to a connected antenna. Additionally other compatible accessories (sold separately) can be connected. ❷ Unbalanced output terminal (6.3 mm mono jack) ❸...
⓮ ❼ ⓫ ⓬ ⓯ ⓭ ❶ ❼ Transmission antenna SYNC button Use to IR SYNC with the receiver (ATW-R3210). ❷ ❽ MUTE switch UP button Switches audio mute on and off. Use to select various settings. ❸ ❾ Indicator BACK button LED that shows the status of the transmitter.
⓮ ❶ ❾ Interchangeable microphone capsule SYNC button ❷ Use to IR SYNC with the receiver (ATW-R3210). Display ❿ Power switch Shows the current status. If no buttons are pressed for a period of 30 seconds, the display Use to turn the power on or off.
How to insert batteries ATW-T3201 ATW-T3202 Slide the battery cover latches down. Rotate the grip case of the battery compartment. Open the battery cover. • Put your finger on the hook of the battery cover and pull it to open the battery cover.
How to attach and detach the interchangeable microphone capsule (only for ATW-T3202) How to attach Attach the microphone capsule to the body of the transmitter. Rotate the microphone capsule clockwise to tighten it. How to remove Rotate the microphone capsule counterclockwise to loosen it. Detach the microphone capsule from the body of the transmitter.
How to read the display ATW-R3210 Main screen ❶ ❷ ❸ ❹ ❺ ❻ VOCAL1 000.000 G 06 C 12 ❼ ❽ ❾ ❿ ⓫ ❶ ❼ Transmitter information display area Group indicator Information on the connected transmitter is displayed. Refer to ❽...
Page 12
How to read the display Level meter screen ❶ ❷ -74 dBm TX - RF PWR -40 -30 -24 -18 -15 -12 -10 -8 -6 -4 -2 0 +2 +4 +6 dBu ❸ ❹ ❺ ❻ ❶ ❹ RF power indicator (transmitter) Audio output indicator (receiver) ❷...
How to read the display ATW-T3201/ATW-T3202 The main screen is displayed when the power is switched on. If you press the UP/Down button on the main screen, the screen display is switched. ❶ ❻ ❼ ❽ 000.000 VOCAL1 02 Ch ❷...
How to operate Basic operation Using IR SYNC Turn on the power button of the receiver (ATW-R3210). This function allows you to make settings on the receiver that are • The display lights and the main screen is displayed. specified for the transmitter.
Various settings can be made from the menu screen shown on the ATW-T3201/ATW-T3202 display. Press the SET button. • The menu screen appears. ATW-R3210 ATW-T3201 ATW-T3202 Press the control dial. • The main menu screen appears. Press the UP/DOWN button to select the item you wish to set.
Setting ATW-R3210 List of setting items Setting by group/channel From the menu screen, turn the control dial, select FREQUENCY MANUAL Set the operating frequency. [FREQUENCY] and then press the control dial. Gr/Ch NAME Set the channel name. AUDIO Set the audio output level.
Setting ATW-R3210 Setting the audio output level Setting transmitters via IR SYNC From the menu screen, turn the control dial, select [AUDIO] and This function allows you to make transmitter settings on the receiver then press the control dial. and then automatically configure the transmitter via IR SYNC. The following are the available settings and setting values: Turn the control dial to set the audio output level.
Setting ATW-R3210 Setting the squelch level Setting the system-related functions Setting automatically Setting the lock From the menu screen, turn the control dial, select [SQUELCH] Set this function to prevent the receiver settings from being changed. and then press the control dial.
Page 19
Setting ATW-R3210 Setting user-defined scan groups Setting the backup frequency mode Aside from the ten preset groups, there are two additional user-defined If you set the backup frequency in advance, you can switch the scan groups: U1 and U2. Both U1 and U2 can be edited with up to 32 frequency of the transmitter and receiver with the transmitter.
Page 20
Setting ATW-R3210 Setting the AF level meter on the main screen Resetting Switch the AF level meter on the main screen between [Receiver (Rx)] This returns the receiver settings to their factory defaults. and [Transmitter (Tx)]. From the menu screen, turn the control dial, select [UTILITIES] •...
Setting ATW-T3201/ATW-T3202 List of setting items Setting by group/channel From the menu screen, press the UP/DOWN button to select FREQUENCY MANUAL Set the transmission frequency. [FREQUENCY], and then press the SET button. Gr/Ch NAME Set the channel name. FREQUENCY GAIN Set the gain.
Setting ATW-T3201/ATW-T3202 Adjusting the gain Setting lock From the menu screen, press the UP/DOWN button to select From the menu screen, press the UP/DOWN button to select [GAIN], and then press the SET button. [LOCK], and then press the SET button. GAIN LOCK Unlock...
Setting ATW-T3201/ATW-T3202 Setting the mute mode (only for ATW-T3201) Setting the indicator The indicator LED can be turned [On] or [Off]. Set the function of the MUTE switch. • The default setting is [On]. From the menu screen, press the UP/DOWN button to select From the menu screen, press the UP/DOWN button to select [MUTE MODE], and then press the SET button.
Page 24
Setting ATW-T3201/ATW-T3202 Resetting This returns the transmitter settings to their factory defaults. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button. UTILITIES Press the UP/DOWN button to select [RESET] and press the SET button.
How to attach the transmitter (ATW-T3201) The ATW-T3201 transmitter is equipped with a clip that can be used to attach the transmitter to a belt, etc. You can reverse the direction of the input connector by Pull both sides of the clip firmly to the outside to remove attaching the clip in the opposite direction.
Achieving stable reception Low RF signal may result if there are obstructions between receiver antennas and transmitter(s). In such a case, reposition the antennas to get better reception. Use external antennas (sold separately) if the installation space is limited. Rack-mounting the receiver •...
Troubleshooting ATW-R3210 Symptoms Causes and countermeasures Reference page The power can't be turned on. Confirm that the AC adapter is correctly connected. There is no voice output. The voice output level is low. Confirm that the transmitter/receiver channels are correct p.
*2 Open range environment with no interfering signals. *3 Frequency response depends on attached microphone element. *4 For assistance with multi-band operation or other frequency coordination issues, Contact your local audio-technica dealer. *5 Region and band dependent ATW-R3210 Receiving system True diversity Image rejection...
Specifications ATW-T3201 RF output power High: 30 mW, Low: 10 mW (switchable), at 50 ohms Spurious emissions Following federal and national regulations Input connection Four pin locking connector Pin 1: GND Pin 2: INST INPUT Pin 3: MIC INPUT Pin 4: DC BIAS +5 V High-pass (low-freq.