Roland FA-07 Reference Manual page 101

For the basic procedure for system settings,
refer to p . 97 .
Synchronization settings (Sync/Tempo)
Parameter Value
Tempo Assign SYSTEM, STUDIO
Source
SET
MASTER
Sync Mode
REMOTE
SLAVE
Sync Output OFF, ON
Clock Source MIDI, USB
Click settings (Click)
Parameter Value
Specifies how the click will be sounded.
OFF
PLAY-ONLY
Click Mode
REC-ONLY
PLAY&REC
ALWAYS
Click Level 0–10
Selects the click sound.
TYPE1
Click Sound
TYPE2
TYPE3
TYPE4
Click Accent
OFF, ON
Switch
Click Output
MAIN, SUB
Assign
Explanation
When you switch studio sets, this
setting specifies whether to use the
current tempo (SYSTEM) or to use the
tempo that is stored in the studio set
(STUDIO SET).
The FA will be the synchronization
master. Choose this setting if you're
using the FA on its own without
synchronizing it to another device, or
if you want the tempo of an external
MIDI device to synchronize with the
FA.
The FA will obey start, continue, stop,
and song position pointer messages
from another device, but the FA's own
tempo setting is used as the playback
tempo.
The FA will be the synchronization
slave. Choose this setting if you want
the FA to synchronize to MIDI clock
messages received from an external
device.
Specifies whether clock, start,
continue, stop, and song position
pointer messages are transmitted
to another device (ON) or are not
transmitted (OFF).
When the Sync Mode is "SLAVE,"
this setting specifies whether the FA
will synchronize to synchronization
messages from the MIDI IN connector
or from the USB port.
Explanation
No click is sounded.
The click sounds when a song is
playing.
The click sounds when a song is being
recorded.
The click sounds when a song is
playing or being recorded.
The click sounds at all times.
Adjusts the click volume.
Conventional metronome sound (first
beat is a bell)
Click sound
Beep sound
Cowbell sound
Adds an accent to the click sound.
Specifies whether the click sound is
output from the MAIN OUTPUT jacks
(MAIN) or from the SUB OUT jack
(SUB).
MIDI settings (MIDI)
Parameter Value
Device ID 17–32
Remote
Keyboard OFF, ON
Switch
Studio Set
Control 1–16, OFF
Channel
USB-MIDI Thru OFF, ON
Transmit
Transmit
Program OFF, ON
Change
Transmit Bank
OFF, ON
Select
Transmit
OFF, ON
Active Sensing
Transmit Edit
OFF, ON
Data
Soft Through OFF, ON
Receive
Receive
Program OFF, ON
Change
Receive Bank
OFF, ON
Select
Receive
OFF, ON
Exclusive
Receive GM
OFF, ON
System On
Receive GM2
OFF, ON
System On
Receive GS
OFF, ON
Reset
Settings for the Entire FA
Explanation
When transmitting and receiving
system exclusive messages, the device
ID numbers of both devices must
match.
"ON"
Turn this if you're using an
external MIDI keyboard instead of the
FA's keyboard. In this case, the MIDI
transmit channel of your external MIDI
keyboard does not matter. Normally,
"OFF."
this can be left at
* If you want to control the
arpeggiator from an external MIDI
"ON."
device, turn this
Specifies the MIDI receive channel
on which MIDI messages (program
change/bank select) from an external
MIDI device will be received by the FA
to switch studio sets.
"OFF"
Choose setting if you don't
want studio sets to be switched from a
connected MIDI device.
Specifies whether MIDI messages
received via the USB COMPUTER
port/MIDI IN connector will be
re-transmitted from the MIDI OUT
connector/USB COMPUTER port (ON)
or not be re-transmitted (OFF) (p. 102).
Specifies whether program change
messages will be transmitted (ON) or
not be transmitted (OFF).
Specifies whether bank select
messages will be transmitted (ON) or
not be transmitted (OFF).
Specifies whether active sensing
messages will be transmitted (ON) or
not be transmitted (OFF).
Specify whether changes you make
in the settings of a studio set will
be transmitted as system exclusive
messages (ON), or will not be
transmitted (OFF).
If this is ON, MIDI messages that are
input from the MIDI IN connector are
re-transmitted without change from
the MIDI OUT connector.
Specifies whether program change
messages will be received (ON) or not
be received (OFF).
Specifies whether bank select
messages will be received (ON) or not
be received (OFF).
Specifies whether system exclusive
messages will be received (ON) or not
be received (OFF).
Specifies whether GM System On
messages will be received (ON) or not
be received (OFF).
Specifies whether GM2 System On
messages will be received (ON) or not
be received (OFF).
Specifies whether GS Reset messages
will be received (ON) or not be
received (OFF).
101