Roland FA-07 Reference Manual page 100

Settings for the Entire FA
Parameter Value
LFO Osc 1
Pulse Width -63–+63
Depth
LFO Osc 2
Pulse Width
-63–+63
Depth
Assignable
Specify the functions that are controlled by the
[ASSIGNABLE]
OFF
CC01–31,
32 (OFF), 33–95
BEND DOWN
BEND UP
AFTERTOUCH
CUTOFF
RESONANCE
ATTACK
RELEASE
PAN
LEVEL
D-Beam Assign
EQ LOW
EQ MID1
EQ MID2
EQ MID3
EQ HIGH
INPUT LEVEL
KNOB ASSIGN1–6
COMPRESSOR
TONE
CHORUS
REVERB
TFX SELECT
TFX CTRL
SAMPLE PAD
Range Max
0–127
Range Min 0–127
Beam Assign STANDARD,
Knob Polarity REVERSE
Beam Assign
Sample Pad 1-1–4-16
Number
100
Explanation
Specifies the depth to which the LFO
will modulate the pulse width of the
Osc 1 waveform.
* The Pulse Width is activated when
"SQR" is selected with Osc 1
waveform.
Specifies the depth to which the LFO
will modulate the pulse width of the
Osc 2 waveform.
*
The Pulse Width is activated when
"SQR" is selected with Osc 2
waveform.
button.
No function is assigned.
Controller number 1–31, 33–95
The same effect as moving the pitch
bend lever to the right.
The same effect as moving the pitch
bend lever to the left.
Aftertouch
Adjusts the cutoff frequency.
Adjusts the resonance.
Adjusts the attack.
Adjusts the release.
Adjusts the pan.
Adjusts the volume.
Adjusts the low frequency range.
Adjusts the mid-1 frequency range.
Adjusts the mid-2 frequency range.
Adjusts the mid-3 frequency range.
Adjusts the high frequency range.
Adjusts the input volume from the
AUDIO INPUT jack.
Adjust the [1] (ASSIGN 1)–[6]
(ASSIGN 6)
knobs.
Adjusts the compressor.
Adjusts the tone.
Adjusts the chorus.
Adjusts the reverb.
Selects the total effect.
Controls the total effect.
Plays a sample.
Specifies the upper limit of the
D-BEAM controller range.
MEMO
By setting the Range Max below
the Range Min, you can invert the
range of variation.
Specifies the lower limit of the
D-BEAM controller range.
STANDARD: The assigned parameter
changes in the positive (+) direction
when you move your hand closer to
the D-BEAM controller.
REVERSE: The assigned parameter
changes in the negative (-) direction
when you move your hand closer to
the D-BEAM controller.
Selects the sample that plays if
D-Beam Assign is set to "SAMPLE
PAD."
Sound settings (Sound)
Parameter Value
Local Switch OFF, ON
Master Tune 415.3–466.2 [Hz]
Master Key
-24–+24
Shift
Master Level
0–127
Output Gain -12–+12 [dB]
Tone Remain OFF, ON
Sample Output
MAIN, SUB
Assign
Wireless Audio
0–127
Level
Wireless
MAIN, SUB
Output Assign
Using the Local Switch setting
If you're using a DAW software with the FA's keyboard
controller section and sound generator section, you should
"OFF."
turn the Local Switch
We need to connect these sections in the following order: the
FA's keyboard a DAW software
Since the FA's keyboard section and sound generator section
are connected internally, such a connection order would
normally be impossible. However, if the Local Switch is
the FA's keyboard section and its sound generator section
will be independent, allowing you to use a DAW software as
shown here in the illustration.
Keyboard
For the basic procedure for system settings,
refer to p . 97 .
Explanation
Enables/disables the connection
between the controller section
(keyboard, pitch bend/modulation
lever, panel knobs and buttons,
D-BEAM controller, pedals, etc.) and
the internal sound engine.
Normally you should leave this
Choose the "OFF" setting if you want
operations on the FA to control only
an external sound module.
Sets the FA's overall tuning (the
frequency of the A4 key).
Shifts the FA's overall pitch range in
semitone steps.
Sets the FA's overall volume.
Adjusts the FA's overall output gain.
Specifies whether the currently
sounding notes will remain (ON) or
not (OFF) when you select a different
sound.
*
In some cases, the effect sound
might not remain.
* If you switch from an organ
SuperNATURAL acoustic tone, the
sound will not remain even if this
setting is "ON."
Specifies whether the sample playback
sound is output from the MAIN
OUTPUT jacks (MAIN) or from the SUB
OUT jack (SUB).
Adjusts the volume that is output via
the wireless LAN function.
When using the wireless LAN function
to output the sound of the FA, this
setting chooses the sound of the MAIN
OUTPUT jacks (MAIN) or the sound of
the SUB OUT jack (SUB).
Here's why.
the FA's sound generator.
Local Off
Sound
generator
DAW software
"ON."
"OFF,"