Marine Network; Evc Network; Setting Alarms; Navigation Alarms - Garmin Volvo Penta GLASS COCKPIT 8x10 Owner's Manual

Naming Devices and Sensors on the Network
You can name devices and sensors connected to the
Garmin Marine Network and the NMEA 2000 network.
1 Select Options > Settings > Communications.
2 Select Marine Network or NMEA 2000 Setup >
Device List.
3 Select a device from the list on the left.
4 Select Review > Change Name.
5 Enter the name, and select Done.

Marine Network

The Marine Network allows you to share data from
Garmin peripheral devices with the chartplotters quickly
and easily. You can connect a chartplotter to the Marine
Network to receive data from and share data with other
devices and chartplotters that are compatible with the
Marine Network.
Select Options > Settings > Communications > Marine
Network.

EVC Network

Select Options > Settings > Communications > EVC
Network, and select a driveline.
For more information, refer to the Volvo Penta manual.
Features: Shows a list of installed EVC features.
Components: Shows a list of installed hardware
components.
Software: Shows a list of software versions for installed
EVC features.
Calibration: Shows a list of installed EVC features that
can be calibrated.

Setting Alarms

The Beeper setting must be turned on to make alarms
audible (Sounds and Display Settings, page
to set audible alarms could lead to injury or property
damage.

Navigation Alarms

Select Options > Settings > Alarms > Navigation.
Arrival: Sets an alarm to sound when you are within a
specified distance or time from a turn or a destination.
Anchor Drag: Sets an alarm to sound when you exceed a
specified drift distance while anchored.
Off Course: Sets an alarm to sound when you are off
course by a specified distance.
Boundary Alarms: Disables and enables all boundary
alarms.
Setting the Anchor Drag Alarm
You can set an alarm to sound if you have moved more
than an allowable distance. This is very useful when
anchoring overnight.
1 Select Options > Settings > Alarms > Navigation >
Anchor Drag.
2 Select Alarm to turn on the alarm.
84
CAUTION
81). Failure
3 Select Set Radius, and select a distance on the chart.
4 Select Back.

System Alarms

Select Options > Settings > Alarms > System.
Clock: Sets an alarm clock.
Unit Voltage: Sets an alarm to sound when the battery
reaches a specified low voltage.
GPS Accuracy: Sets an alarm to sound when the GPS
location accuracy falls outside the user-defined value.

Sonar Alarms

The sonar alarms feature is a tool for situational
awareness only and may not prevent grounding in
all circumstances. It is your obligation to ensure safe
operation of the vessel.
The Beeper setting must be turned on to make alarms
audible (Sounds and Display Settings, page
to set audible alarms could lead to injury or property
damage.
NOTE: Not all options are available on all transducers.
From an applicable sonar view, select Options > Sonar
Setup > Alarms.
You can also open the sonar alarms by selecting Options
> Settings > Alarms > Sonar.
Shallow Water: Sets an alarm to sound when the depth is
less than the specified value.
Deep Water: Sets an alarm to sound when the depth is
greater than the specified value.
FrontVü Alarm: Sets an alarm to sound when the depth
in front of the vessel is less than the specified value,
which can help you avoid running aground
FrontVü Depth Alarm, page
only with Panoptix FrontVü transducers.
Water Temp.: Sets an alarm to sound when the
transducer reports a temperature that is 2°F (1.1°C)
above or below the specified temperature.
Contour: Sets an alarm to sound when the transducer
detects a suspended target within the specified depth
from the surface of the water and from the bottom.
Fish: Sets an alarm to sound when the device detects a
suspended target.
• sets the alarm to sound when fish of all sizes
are detected.
• sets the alarm to sound only when medium or
large fish are detected.
• sets the alarm to sound only when large fish are
detected.

Setting Weather Alarms

Before you can set weather alarms, you must have a
compatible chartplotter connected to a weather device,
WARNING
CAUTION
81). Failure
(Setting the
46). This alarm is available
Device Configuration