Realvü Appearance Settings; Panoptix Transducer Installation Settings - Garmin Volvo Penta GLASS COCKPIT 8x10 Owner's Manual

offset when using the front collision alarm
Bow Offset, page 48).
1 From the FrontVü sonar view, select Options >
FrontVü Alarm.
2 Select On.
3 Enter the depth at which the alarm is triggered, and
select Done.
On the FrontVü screen, a depth line shows the depth
at which the alarm is set. The line is green when you
are in a safe depth. The line turns yellow when you are
going faster than the forward range gives you time to react
(10 seconds). It turns red and sounds an alarm when the
system detects an obstruction or the depth is less than the
entered value.
LiveVü and FrontVü Appearance Settings
From a LiveVü or FrontVü Panoptix sonar view, select
Options > Sonar Setup > Appearance.
Color Scheme: Sets the color palette.
Color Gain: Adjusts the intensity of colors shown on the
screen.
You can select a higher color gain value to see targets
higher in the water column. A higher color gain value
also allow you to differentiate low intensity returns
higher in the water column, but this causes a loss in
the differentiation of the returns at the bottom. You can
select a lower color gain value when targets are near
the bottom, to help you distinguish between targets and
high intensity returns such as sand, rock, and mud.
Trails: Sets the how long the trails appear on the screen.
The trails show the movement of the target.
Bottom Fill: Colors the bottom brown to distinguish it from
the water returns.
LiveVü and FrontVü Layout Settings
From a LiveVü or FrontVü Panoptix sonar view, select
Options > Sonar Setup > Layout.
Grid Overlay: Shows a grid of range lines.
Scroll History: Shows the sonar history on the side of the
screen.
Beam Icon: Selects the icon used to show the direction of
the transducer beam.
On-screen Control: Shows the on-screen buttons.
Compress Range: In forward views, compresses the
forward range farther away from the boat and expands
the range closer to the boat. This allows you to
see closer objects more clearly while keeping farther
objects on the screen.
RealVü Appearance Settings
From a RealVü sonar view, select Options > Sonar
Setup > Appearance.
Point Colors: Sets a different color palette for the sonar
return points.
Bottom Colors: Sets the color scheme for the bottom.
Sonar Fishfinder
(Setting the Bottom Style: Sets the style for the bottom. When you
are in deep water, you can select the Points option and
manually set the range to a shallower value.
Color Key: Shows a legend of the depths the colors
represent.
On-screen Control: Shows or hides the on-screen
buttons.

Panoptix Transducer Installation Settings

From a Panoptix sonar view, select Options > Sonar
Setup > Installation.
Install Depth: Sets the depth below the water line where
the Panoptix transducer is mounted. Entering the actual
depth at which the transducer is mounted results in
a more accurate visual presentation of what is in the
water.
Bow Offset: Sets the distance between the bow and the
forward view Panoptix transducer installation location.
This allows you to view the forward distance from the
bow instead of the transducer location.
This applies to Panoptix transducers in the FrontVü,
LiveVü Forward, and RealVü 3D Forward sonar views.
Beam Width: Sets the width of the down view Panoptix
transducer beam. Narrow beam widths allow you to see
deeper and farther. Wider beam widths allow you to
see more coverage area.
This applies to Panoptix transducers in the FrontVü,
LiveVü Down, and LiveVü Forward sonar views.
Use AHRS: Enables the internal attitude heading
and reference system (AHRS) sensors to detect
the installation angle of the Panoptix transducer
automatically. When this setting is turned off, you can
enter the specific installation angle for the transducer
using the Pitch Angle setting. Many forward view
transducers are installed at a 45-degree angle and
down view transducers are installed at a zero-degree
angle.
Flipped: Sets the orientation of the Panoptix sonar view
when the down view transducer is installed with the
cables pointing toward the port side of the boat.
This applies to Panoptix transducers in the LiveVü
Down, RealVü 3D Down, and RealVü 3D Historical
sonar views.
Calibrate Compass: Calibrates the internal compass
in the Panoptix transducer
page
This applies to Panoptix transducers with an internal
compass, such as the PS21-TR transducer.
Orientation: Controls if the transducer is in down or
forward installation mode. The Auto setting uses the
AHRS sensor to determine the orientation.
This applies to PS22 transducers.
Restore Sonar Defaults: Restores the sonar settings to
the factory default values.
(Calibrating the Compass,
48).
47