Omron E3C-LDA Series Manual page 53

Ratings and Specifications
Sensing
method
Model
NPN output
PNP output
Item
Sensing distance
Spot diameter
Standard sensing object
Differential travel
Black/white error
Directional angle
Light source (wavelength)
Power supply voltage
Current consumption
Control output
Protection circuits
Response time
Sensitivity adjustment
Ambient illumination
(Receiver side)
Ambient temperature range
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Degree of protection *
Connection method
Indicator
Weight Pre-wired models
(packed
Connector models
state)
Housing
Lens
Indication
Materials
Sensitivity adjustment
and mode selector
switch
Seals
Accessories
* IP69K Degree of Protection Specification
IP69K is a protection standard against high temperature and high-pressure water defined in the German standard DIN 40050,
Part 9. The test piece is sprayed with water at 80°C at a water pressure of 80 to 100 BAR using a specified nozzle shape
at a rate of 14 to 16 liters/min.
The distance between the test piece and nozzle is 10 to 15 cm, and water is sprayed horizontally for 30 seconds
each at 0°, 30°, 60°, and 90° while rotating the test piece on a horizontal plane.
6
Oil-resistant, Robust, Compact Photoelectric Sensor
Through-beam
E3ZM-CT61 (-M1TJ) E3ZM-CT62B (-M1TJ)
E3ZM-CT66 E3ZM-CT67B
E3ZM-CT81 (-M1TJ) E3ZM-CT82B (-M1TJ)
E3ZM-CT86 E3ZM-CT87B
15 m 20 m
Opaque: 12-mm dia. min.
Emitter, Receiver: 3° to 15°
(Distance between emitter and receiver. Rated sensing
distance)
Infrared LED (870 nm) Orange LED (615 nm)
10 to 30 VDC, including 10% ripple (p-p)
40 mA (Emitter 20 mA max., Receiver 20 mA max.)
Load power supply voltage: 30 VDC max., Load current: 100 mA max. (Residual voltage: 2 V max.)
Open-collector output (NPN/PNP output depending on model)
Light-ON/Dark-ON switch selectable
Reversed power supply polarity protection, Output short-
circuit protection, and Reversed output polarity protec-
tion
Operate or reset: Operate or reset:
1 ms max. 2 ms max.
One-turn adjuster
Incandescent lamp: 3,000 lx max., Sunlight: 10,000 lx max.
Operating: − 25 to 55°C, Storage: − 40 to 70°C (with no icing or condensation)
Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
20 M Ω min. at 500 VDC
1,000 VAC, 50/60 Hz for 1 min
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
2
Destruction: 500 m/s 3 times each in X, Y, and Z directions
IEC: IP67, DIN 40050-9: IP69K
-C@@1/-C@@2(B): Pre-wired cable (standard length: 2 m, -M1TJ: Pre-wired connector with 0.3-m cable)
-C@@6/-C@@7(B): M8 4-pin connector
Operation indicator (yellow), Stability indicator (green) (Emitter has only power supply indicator (green).)
Approx. 150 g (-M1TJ: Approx. 90 g)
Approx. 60 g
SUS316L
PMMA (polymethylmethacrylate)
PES (polyethersulfone)
PEEK (polyetheretherketone)
Fluoro rubber
Instruction sheet (Note: Reflectors and Mounting Brackets are sold separately.)
Retro-reflective with
MSR function
E3ZM-CR61 (-M1TJ)
E3ZM-CR66
E3ZM-CR81 (-M1TJ)
E3ZM-CR86
4 m [100 mm]
(Using E39-R1S)
3 m [100 mm]
(Using E39-R1)
---
Opaque: 75-mm dia. min.
---
---
Sensor: 3° to 10°
Reflector: 30° (Distance to
Reflector. Rated sensing
distance)
Red LED (660 nm)
25 mA max.
Reversed power supply polarity protection, Output
short-circuit protection, Reversed output polarity protec-
tion, and Mutual interference prevention
Operate or reset: 1 ms max.
Approx. 90 g (-M1TJ: Approx. 50 g)
Approx. 40 g
E3ZM-C
Diffuse-reflective
E3ZM-CD62 (-M1TJ)
E3ZM-CD67
E3ZM-CD82 (-M1TJ)
E3ZM-CD87
1 m
(White paper
300 × 300 mm)
---
20% of sensing distance
max.
---
Infrared LED (860 nm)