Table of Contents
Advertisement
[DRS]
Item
[DRS]
[EFFECT DEPTH]
[DETAIL SETTING]
Item
[DETAIL]
[MASTER DETAIL]
[H DETAIL LEVEL]
[V DETAIL LEVEL]
[PEAK FREQUENCY]
[V DETAIL FREQUENCY]
[CRISP]
[DETAIL GAIN(+)]
[DETAIL GAIN(−)]
[DETAIL CLIP+]
[DETAIL CLIP−]
[DETAIL SOURCE]
[KNEE APERTURE LEVEL]
[DETAIL KNEE]
[LEVEL DEPENDENT SWITCH]
[LEVEL DEPENDENT]
[DARK DETAIL SWITCH]
Chapter 4 Menu Operations — Menu list
Enables/disables the dynamic range stretcher function. Set this to [ON] to automatically adjust the
contrast.
This cannot be set in HDR mode.
[OFF], [ON]
f Factory setting: [OFF]
Sets the compression level of the high-luminance areas of the dynamic range stretcher function. Set a
larger value to increase the compression level of the high-luminance areas.
[1]...[5]
f Factory setting: [5]
Enables/disables all detail functions.
[OFF], [ON]
f Factory setting: [ON]
Sets the master detail.
[−31]...[+31]
f Factory setting: [0]
Sets the correction level of the horizontal detail.
[00]...[63]
f Factory setting: [15]
Sets the correction level of the vertical detail.
[00]...[63]
f Factory setting: [20]
Sets the peak frequency of the horizontal detail.
[12.4MHz], [12.5MHz], [12.7MHz], [12.9MHz], [13.0MHz], [13.3MHz], [13.6MHz], [13.9MHz], [14.2MHz],
[14.6MHz], [15.0MHz], [15.5MHz], [16.1MHz], [16.7MHz], [17.3MHz], [18.3MHz], [18.6MHz], [18.8MHz],
[19.0MHz], [19.2MHz], [19.5MHz], [19.9MHz], [20.3MHz], [20.9MHz], [21.5MHz], [22.4MHz], [23.6MHz],
[25.4MHz], [28.6MHz], [37.1MHz]
f Factory setting: [19.0MHz]
Sets the vertical detail frequency.
[00]...[31]
f Factory setting: [18]
Sets the detail signal noise removal level.
[00]...[63]
f Factory setting: [0]
Sets the detail level in the + (upward) direction.
[−31]...[+31]
f Factory setting: [0]
Sets the detail level in the − (downward) direction.
[−31]...[+31]
f Factory setting: [0]
Adjust the detail clip to reduce glare produced by an excess of details.
[00]...[63]
f Factory setting: [0]
Adjusts the length of the undershoot of the detail edge component.
[00]...[63]
f Factory setting: [0]
Sets the RGB signal component ratio to create the detail.
[(G+R)/2], [(G+B)/2], [(2G+B+R)/4], [(3G+R)/4], [R], [G]
f Factory setting: [(G+R)/2]
Adjusts the knee aperture level.
This cannot be set in HDR mode.
[00]...[39]
f Factory setting: [5]
Adjusts the detail components of knee.
[00]...[15]
f Factory setting: [0]
Enables/disables the function to remove details of dark areas.
This cannot be set in HDR mode.
[OFF], [ON]
f Factory setting: [OFF]
Sets the level to remove details of dark areas.
[00]...[15]
f Factory setting: [8]
Enables/disables the function to emphasize details of dark areas.
This cannot be set in HDR mode.
[OFF], [ON]
f Factory setting: [OFF]
– 61 –
Description of settings
Description of settings
Advertisement
Table of Contents
