Related Manuals for Teledyne Princeton Instruments FER785-MM
Summary of Contents for Teledyne Princeton Instruments FER785-MM
- Page 1 FER785-MM Diode Laser Source User Manual 4411-0157 Issue 2 March 29, 2019 www.princetoninstruments.com...
- Page 2 Trenton, NJ 08619 TEL: 800-874-9789 / 609-587-9797 FAX: 609-587-1970 All rights reserved. No part of this publication may be reproduced by any means without the written permission of Teledyne Princeton Instruments. Printed in the United States of America. Pentium is a registered trademark of Intel Corporation.
-
Page 3: Table Of Contents
Table of Contents Chapter 1: About this Document......... 5 Intended Audience . - Page 4 FER785-MM Diode Laser Source User Manual Issue 2 List of Figures Figure 1-1: Typical Laser Aperture Label ........7 Figure 1-2: Typical Laser Warning Label .
-
Page 5: Chapter 1: About This Document
FER785-MM Diode Laser Source Data Sheet Teledyne Princeton Instruments maintains updated documentation and user manuals on their FTP site. Visit the Teledyne Princeton Instruments FTP Site to verify that the most recent user manual is available and being referenced: ftp://ftp.piacton.com/Public/Manuals/Princeton Instruments... -
Page 6: Document Organization
FER785-MM Diode Laser Source User Manual Issue 2 Document Organization This manual includes the following chapters and appendices: • Chapter 1, About this Document Provides information about the organization of this document, as well as related documents, safety information, and conventions used throughout the manual. -
Page 7: Fer785-Mm Diode Laser Source Safety Information
Chapter 1 About this Document FER785-MM Diode Laser Source Safety Information This section provides critical safety information when using an FER785-MM Diode Laser Source. WARNING! There are no user-serviceable parts within an FER785-MM Diode Laser Source enclosure. WARNING! Use of controls or adjustments, or the performance of procedures other than those specified within this document, may result in hazardous radiation exposure 1.5.1... - Page 8 FER785-MM Diode Laser Source User Manual Issue 2 This page is intentionally blank.
-
Page 9: Chapter 2: Fer785-Mm Diode Laser Source
Chapter 2: FER785-MM Diode Laser Source The FER785-MM Diode Laser Source is well suited for bench top fiber coupled experiments including Raman spectroscopy. The laser housing contains a 785 nm wavelength stabilized multi-mode diode laser with programmable power output up to 475 mW CW. -
Page 10: Mounting An Fer785-Mm Diode Laser Source
FER785-MM Diode Laser Source User Manual Issue 2 Mounting an FER785-MM Diode Laser Source Although not necessary for operation, the FER785-MM Diode Laser Source can be secured to an optical breadboard using the supplied adapter plate. To secure the FER785-MM Diode Laser Source, insert the screws provided into the plate and secure them to the bottom of the housing. -
Page 11: Operation
Chapter 3: Operation WARNING! Always observe proper laser safety when operating this source. This chapter provides information about the use and operation of the FER785-MM Diode Laser Source. Remove the Dust Cap/Beam Attenuator that is secured to the FC/PC fiber terminal. Figure 3-1. -
Page 12: Figure 3-2: Fer785-Mm Diode Laser Source: Rear Of Housing
FER785-MM Diode Laser Source User Manual Issue 2 4. Insert the Safety Key Card into the slot labeled KEY on the rear of the laser housing. Figure 3-2. Figure 3-2: FER785-MM Diode Laser Source: Rear of Housing DC P OWER NPUT USB 2.0 P EMOTE... -
Page 13: Figure 3-3: Typical Fer785-Mm Diode Laser Source: Power On
3-3. Figure 3-3: Typical FER785-MM Diode Laser Source: Power On MBER ONSTANT 9. Laser output power can now be controlled using Teledyne Princeton Instruments LightField software. NOTE: The laser source always defaults to its nominal output power rating following startup. -
Page 14: Figure 3-4: Typical Fer785-Mm Diode Laser Source: Gate Mode
FER785-MM Diode Laser Source User Manual Issue 2 10. Pressing the power button on the front of the housing a SECOND time switches the laser to GATE (or PULSE) mode. NOTE: Laser radiation is emitted only when the incoming signal at the PULSE input on the rear of the laser housing is HIGH. -
Page 15: Chapter 4: Remote Safety Interlock Connections
Chapter 4: Remote Safety Interlock Connections The FER785-MM Diode Laser Source is equipped with a 3.5 mm mono jack Remote Safety Interlock connector located on the rear of the laser housing. See Figure 4-1. Figure 4-1: FER785-MM Diode Laser Source Remote Safety Interlock Connector EMOTE AFETY NTERLOCK... - Page 16 FER785-MM Diode Laser Source User Manual Issue 2 All FER785-MM Diode Laser Source units are shipped with a 3.5 mm shorting pin pre-installed on the ILOK connector. • If the Remote Interlock feature will not be utilized, this shorting pin should remain in place, and the FER785-MM Diode Laser Source will operate normally.
-
Page 17: Appendix A: Technical Specifications
Technical Specifications CAUTION! All specifications are subject to change. This appendix provides technical specifications for the FER785-MM Diode Laser Source. Additional information may be found on data sheets available on the Teledyne Princeton Instruments website (www.princetoninstruments.com). Assembly Part Numbers Refer to Table A-1 for assembly part numbers. -
Page 18: Diode Laser Specifications
FER785-MM Diode Laser Source User Manual Issue 2 Diode Laser Specifications Refer to Table A-3 for diode laser specifications. Table A-3: FER785-MM Diode Laser Source Technical Specifications Parameter Specification Output Coupling FC/PC Wavelength 785 nm Wavelength Tolerance ±0.5 nm Spectral Line Width <0.15 nm Side Mode Suppression Ratio 35 –... -
Page 19: Environmental Specifications
Appendix A Technical Specifications Refer to Table A-4 for power specifications for the FER785-MM Diode Laser Source external power supply. Table A-4: Power Specifications: External FER785-MM Diode Laser Source Power Supply Specification Parameter Unit Minimum Nominal Maximum Input Voltage Input Frequency Input Current —... - Page 20 FER785-MM Diode Laser Source User Manual Issue 2 This page is intentionally blank.
-
Page 21: Appendix B: Outline Drawings
Appendix B: Outline Drawings NOTE: All dimensions are provided in inches [mm]. FER785-MM Diode Laser Source Figure B-1: Outline Drawing: FER785-MM Diode Laser Source (sheet 1 of 2) - Page 22 FER785-MM Diode Laser Source User Manual Issue 2 Figure B-1: Outline Drawing: FER785-MM Diode Laser Source (sheet 2 of 2) 0.00 0.250 REMOVABLE MOUNTING PLATE 0.089 2.26 THRU 4-40 UNC THRU 6 3.20 0.125[3.18] 2.271 57.67 1.866 47.39 1.679 42.65 PROTECTIVE COVER 0.871 22.12...
-
Page 23: Warranty And Service
(1) year after shipment. During this period, Teledyne Princeton Instruments will repair the product or, at its sole option, repair or replace any defective part without charge to you. You must deliver the entire product to the Teledyne Princeton Instruments factory or, at our option, to a factory-authorized service center. -
Page 24: Sealed Chamber Integrity Limited 12 Month Warranty
(1) year from shipment. Teledyne Princeton Instruments does not warrant that the function of the software will meet your requirements or that operation will be uninterrupted or error free. -
Page 25: Owner's Manual And Troubleshooting
3. All warranty service must be made by the Teledyne Princeton Instruments factory or, at our option, an authorized service center. 4. Before products or parts can be returned for service you must contact the Teledyne Princeton Instruments factory and receive a return authorization number (RMA.) Products or parts returned for service without a return authorization evidenced by an RMA will be sent back freight collect. -
Page 26: Contact Information
In no event shall Teledyne Princeton Instruments’ liability exceed the cost of the repair or replacement of the defective product or part. - Page 27 This page is intentionally blank.
- Page 28 info@princetoninstruments.com USA +1 877-474-2286 | France +33 (1) 60 86 03 65 | Germany +49 (0) 89 660 7793 | UK & Ireland +44 (0) 1628 472 346 Singapore +65 6408 6240 | China +86 10 659 16460 | Japan +81 (3) 5639 2741...