Canon XF100 Instruction Manual page 104

Custom Picture Settings
Sharpness
Sets the sharpness of the output and recording signal.
[Level]: Sets the sharpness level. This setting can be adjusted from -10 to 50. (Default: 0)
[H Detail Freq.]: Sets the center frequency of horizontal sharpness. Setting higher values increases the
104
frequency, which, in turn, increases the sharpness. This setting can be adjusted from -8 to 8.
(Default: 0)
[Coring]: Reduces noise artifacts caused by high sharpness levels.
[Level]: Sets the coring level. Higher values prevent sharpness from being applied to minute details, resulting in
less noise. This setting can be adjusted from -30 to 50. (Default: 0)
[D-Ofst]: You can use [D-Ofst], [D-Curve] and [D-Depth] to adjust the coring level based on brightness. [D-Ofst]
sets the coring level of the minimum brightness level. This setting can be adjusted from 0 to 50. (Default: 0)
[D-Curve]: Sets the curve of the coring adjustment. This curve is the change from [Level] to [D-Ofst]. This setting
can be adjusted from 0 to 8. (Default: 0)
[D-Depth]: Sets a multiplier to [D-Ofst] that determines the coring level adjustment based on brightness.
Positive values raise the coring level in dark areas and negative values lower the level. This setting can be
adjusted from -4 to 4. (Default: 0)
[HV Detail Bal.]: Adjusts the ratio between horizontal and vertical detail. Higher values emphasize vertical detail
while lower values emphasize horizontal detail. This setting can be adjusted from -8 to 8.
(Default: 0)
[Limit]: Restricts how much sharpness is applied. This setting can be adjusted from -50 to 50.
(Default: 0)
[Knee Aperture]: Allows you to set the sharpness of only the areas above the knee point by adjusting the gain and
slope. This is not available when [Gamma] is set to [Cine 1] or [Cine 2].
[Gain]: Sets the amount of sharpness. This setting can be adjusted from 0 to 9. (Default: 0)
[Slope]: Sets the slope of the sharpness. This setting can be adjusted from 0 to 3, with 0 having no slope,
1 having a steep slope and 3 having a gradual slope. (Default: 1)
[Level Depend]: Lowers the amount of sharpness applied to dark areas of the image.
[Level]: Sets the brightness of the dark areas of the image that will be affected. This setting can be adjusted
from 0 to 50. (Default: 0)
[Slope]: Determines the slope of the area between the upper and lower parts of the gamma curve. This setting
can be adjusted from 0 to 3, with 0 having no slope, 1 having a steep slope and 3 having a gradual slope.
(Default: 0)
[Offset]: Adjusts the sharpness level of dark areas in the image. Setting higher values will lower the sharpness
level. This setting can be adjusted from 0 to 50. (Default: 0)
[Ingredient Ratio]: Changing this ratio allows you to affect the balance between resolution and the reduction of
Noise Reduction
Reduces the amount of noise that appears in the image. Select [Automatic] to have the camcorder adjust the
noise automatically. Otherwise, select a level from 1 (lowest level) to 8 (highest level), or select [Off] to turn the
noise reduction off. (Default: [Automatic])
Skin Detail
The camcorder applies a softening filter to areas in the picture with skin tones to give a more pleasant
appearance. By changing these settings, you can determine what areas will be detected as skin tones. A zebra
pattern will appear over areas on the LCD screen that are detected as having skin tones.
[Effect Level]: Adjusts the level of the filter. The available options are [Off], [Low], [Middle] and [High].
(Default: [Off])
[Hue]: Adjusts the hue for detection of skin tones. This setting can be adjusted from -16 to 16. (Default: 0)
jagged edges. Higher values emphasize resolution while lower values emphasize the
reduction of jagged edges. This setting can be adjusted from -50 to 50. (Default: 0)