Grizzly G0941 Manual page 24

613
The Model G0941
spreader/riving knife is
0.09" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:
BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.082"
• Min. Kerf Thickness: 0.114"
• Must be aligned with
spreader or riving knife.
Dado Blades
• Dado blades under 10"
diameter not compatible
with riving knife.
• Max Width: 3/4"
611
10" 3 HP CABINET TABLE SAW
Specifications
Motor: 3 HP, 220V, Single-Phase, 60 Hz
To reduce risk of serious injury when using this machine:
Full-Load Current Rating: 13A
1. Read and understand owner's manual before operating.
Blade Size: 10" x 5/8" Arbor
2. Never touch moving blade and keep hands out of cutting path.
Minimum Blade Kerf Thickness: 0.114"
3. Always wear approved eye protection and respirator.
Arbor Speed: 4000 RPM
4. Only plug power cord into a grounded outlet.
Max. Rip Capacity: 36"
5. Always use blade guard/spreader for all through cuts; and use
Max. Depth of Cut at 90˚: 3-3/16"
riving knife for all non-through cuts. If certain cut cannot be
Max. Depth of Cut at 45˚: 2-3/16"
made with either device, some other safeguard MUST be used.
Max. Dado Width: 3/4"
Weight: 474 lbs. 6. Only use blades meeting size/speed requirements for saw.
7. Ensure spreader/riving knife and fence are properly adjusted.
Date 8. Never reach behind or over blade while it is moving.
9. Use a push stick when required and whenever possible,
especially with small/narrow workpieces and non-through
S/N
cuts.
Mfd. for Grizzly in Taiwan 10. Know what causes "kickback" and how to prevent it.
610
REF PART # DESCRIPTION
601 P0941601 UL 987 WARNING LABEL
602 P0941602 KEEP DOOR CLOSED LABEL
603 P0941603 READ MANUAL LABEL
604 P0941604 BLADE GUARD LABEL
605 P0941605 EYE/LUNG INJURY LABEL
606 P0941606 HANDWHEEL NOTICE LABEL
607 P0941607 MODEL NUMBER LABEL
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
BUY PARTS ONLINE AT GRIZZLY.COM!
-24-
Scan QR code to visit our Parts Store.
Labels & Cosmetics
602
601
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.
612
MODEL G0941
WARNING!
11. Never remove jammed/cutoff workpiece when blade is moving!
12. Make sure blade is stopped before adjusting height/tilt.
13. Do not perform any operation freehand.
14. Never use fence and miter gauge at same time.
15. Ensure machine is stable and fence is parallel with blade.
16. Disconnect power before changing blades or servicing saw.
17. Plan cuts so that workpieces always remain supported.
18. Non-though cuts (i.e. dadoes, rabbets, moulding cuts) and
resawing cuts present specific dangers; refer to manual.
19. Do not wear loose clothing, gloves, jewelry, or other items that
can get entangled. Tie back long hair and roll up sleeves.
20. Do not expose to rain or operate in wet environment.
21. Prevent unauthorized use by children or untrained users;
restrict access or disable machine when unattended.
603
WARNING!
609
REF PART #
608 P0941608
609 P0941609
610 P0941610
611 P0941611
612 P0941612
613 P0941613
604
AMPUTATION
Removing blade If blade guard is
HAZARD!
guard increases removed for a
Always keep
risk of injury—it special cut, some
fingers and
MUST be installed other safeguard
hands away from
when possible. MUST be used.
moving blade.
605
WARNING!
EYE/LUNG INJURY
HAZARD!
606
Always wear safety
glasses and a
respirator when
using this machine
Rotating blade adjustment handwheels into
stopping positions with excessive force could
result in a loss of blade parallelism with miter
slot, impaired stop-collar accuracy, and
damage to internal components. This type of
damage is not covered by warranty!
607
G0941
608
DESCRIPTION
TOUCH-UP PAINT, GRIZZLY GREEN
GRIZZLY NAMEPLATE
MACHINE ID LABEL
BLADE REQUIREMENT LABEL
DISCONNECT POWER LABEL
ELECTRICITY LABEL
Model G0941 (Mfd. Since 09/20)
Disconnect power
before changing
blades or blade
guard and riving
knife.