Receiving And Handling The Product; Visual Inspection - Mitsubishi Electric Climaveneta i-BX-004-013M Installation, Operation And Service Manual

RECEIVING AND HANDLING THE PRODUCT

VISUAL INSPECTION

When the items are consigned by the carrier:
- make sure that the goods delivered correspond to the
description on the delivery note, comparing this against
the data on the packaging label.
- make sure the packaging and the unit are intact.
If damage or missing components are noted, indicate this on
the delivery note. A formal complaint should be sent via fax
or registered post to the After Sales Department within eight
days from the date of receipt of the items.
HANDLING PACKAGED UNITS
The unit should always be handled by qualified personnel
using equipment adequate for the weight of the unit, in com-
pliance with the safety standards in force (and subsequent
amendments).
• Lifting by forklift (1)
Insert the forks under the long side of base, opening the
forks as fare as possible.
• Lifting by crane (2)
To lift the unit, insert tubes long enough to allow position-
ing of the lifting slings and safety pins in the special feet
on the unit.
For the sizes of these tubes, see the figures shown in the
corresponding section. To avoid the slings damaging the
unit, place protection between the slings and the unit.
i-BX-(Y) dimensions and packaged weight
Size
Dimension L
Dimension P
Dimension H
Weight
Max no. of stackable units
i-BX-(Y) dimensions and weight with wooden crate
Size
Dimension L
Dimension P
Dimension H
Weight
Max no. of stackable units
i-BX-N-(Y) dimensions and packaged weight
Size
Dimension L
Dimension P
Dimension H
Weight
Max no. of stackable units
i-BX-N-(Y) dimensions and weight with wooden crate
Size
Dimension L
Dimension P
Dimension H
Weight
Max no. of stackable units
6 i-BX-(Y)_i-BX-N-(Y) EN
04 06
mm 990 990
mm 490 490
mm 1090 1090 1390
kg 90 95
No. 1 1
04 06
mm 1040 1040 1040
mm 545 545
mm 1170 1170 1470
kg 115 120
No. 1 1
04 06
mm 990 990
mm 490 490
mm 1090 1090 1390
kg 95 100
No. 1 1
04 06
mm 1040 1040 1040
mm 545 545
mm 1170 1170 1470
kg 120 125
No. 1 1
STORING THE UNITS
The units must be stored sheltered from direct sunlight, rain,
wind or sand.
Avoid exposing the units to direct sunlight, as the pressure
inside the refrigerant circuit may reach dangerous values
and cause the activation of the safety valves, where fitted.
The units cannot be stacked.
L
08 10 13
990 990 990
540 540 540
1390 1390 1540
110 125 140
1 1 1
08 10 13
1040 1040 1040
595 595 595
1470 1470 1620
140 155 170
1 1 1
08 10 13
990 990 990 1530
540 540 540
1390 1540 1400
115 130 150
1 1 1
08 10 13
1040 1040 1630
595 595 595
1470 1620 1450
145 160 185
1 1 1
2
H
P
1
15 20 25
990 1530 1530 1530
540 700 700
1400 1900 1900
155 210 270
1 1 1
15 20 25
1630 1630 1630
595 750 750
1450 1950 1950
190 250 320
1 1 1
15 20 25
1530 1530 1530
700 700 700
1400 1900 1900
200 225 285
1 1 1
15 20 25
1630 1630 1630
750 750 750
1450 1950 1950
240 265 335
1 1 1
I A
Bar code
(compressor side)
30 35
1780
700 800
1900
290 325
1 1
30 35
1880
750 850
1950
340 380
1 1
30 35
1780
700 800
1900
310 345
1 1
30 35
1880
750 850
1950
360 400
1 1