Chorus; Flanger - Roland Aerophone Pro Parameter Manual

MFX/IFX Parameters

23 Chorus

This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
Balance D
L in
Chorus
Chorus
R in
Balance D
Parameter Value
Filter Type
OFF, LPF, HPF
200, 250, 315, 400,
500, 630, 800, 1000,
1250, 1600, 2000,
Cutoff Freq
2500, 3150, 4000,
5000, 6300, 8000
(Hz)
Pre Delay 0.0–100 (msec)
Rate (sync sw) OFF, ON
Rate (Hz) 0.05–10.00 (Hz)
Note
Rate (note)
&
"Note" (p. 64)
Depth 0–127
Phase
0–180 (deg)
Low Gain -15–+15 (dB)
High Gain
-15–+15 (dB)
Balance D100:0W–D0:100W
Level
0–127
54
L out
2-Band EQ
Balance W
Balance W
R out
2-Band EQ
Explanation
Type of filter
OFF: No filter is used.
LPF: Cuts the frequency range above the
Cutoff Freq
HPF:
Cuts the frequency range below the
Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from the direct
sound until the chorus sound is heard.
If this is ON, the rate synchronizes with the
tempo of the rhythm.
&
"Scene Tempo" (p. 22)
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Gain of the low range
Gain of the high range
Volume balance between the direct sound
(D) and the chorus sound (W)
Output Level

24 Flanger

This is a stereo flanger (The LFO has the same phase for left and
right.).
It produces a metallic resonance that rises and falls like a jet airplane
taking off or landing.
A filter is provided so that you can adjust the timbre of the flanged
sound.
L in
Flanger
Feedback
Feedback
Flanger
R in
Parameter Value
Filter Type
OFF, LPF, HPF
200, 250, 315, 400,
500, 630, 800, 1000,
1250, 1600, 2000,
Cutoff Freq
2500, 3150, 4000,
5000, 6300, 8000
(Hz)
Pre Delay
0.0–100 (msec)
Rate (sync sw)
OFF, ON
Rate (Hz) 0.05–10.00 (Hz)
Note
Rate (note)
&
"Note" (p. 64)
Depth 0–127
Phase 0–180 (deg)
Feedback
-98–+98 (%)
Low Gain -15–+15 (dB)
High Gain -15–+15 (dB)
Balance D100:0W–D0:100W
Level 0–127
Balance D
2-Band EQ
Balance W
Balance W
2-Band EQ
Balance D
Explanation
Type of filter
OFF:
No filter is used.
LPF:
Cuts the frequency range above the
Cutoff Freq
HPF:
Cuts the frequency range below the
Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from the direct
sound until the flanger sound is heard.
If this is ON, the rate synchronizes with
the tempo of the rhythm.
&
"Scene Tempo" (p. 22)
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the flanger
sound that is fed back into the effect.
Negative (-) settings will invert the phase.
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the flanger sound (W)
Output Level
L out
R out