Scene/Reverb; Reverb Parameters - Roland Aerophone Pro Parameter Manual

SCENE/REVERB

Parameter Value
RV SW
OFF, ON
Selects the types of reverb.
Reverb Type
OFF, 1 INTEGRA7Rev, 2 Warm Hall, 3 Hall, 4 GS Reverb, 5 SRV-2000, 6 SRV-2000NL, 7 GM2 Reverb
FX
Configure the parameters of the selected reverb type.

Reverb parameters

See "Reverb parameters"
OUTPUT
Reverb Level
0–127
Reverb Parameters
1 INTEGRA7Rev (INTEGRA 7 Reverb)
Parameter Value
ROOM1–2,
Char HALL1–2,
PLATE
PreDelay
0–100
Time 0.1–10.0 (sec)
Density 0–127
Diffusion 0–127
LF Damp 0–100
HF Damp 0–100
Spread 0–127
Tone 0–127
Explanation
Switches the reverb on/off.
The available parameters differ depending on the type of reverb you selected in
Reverb Type.
Sets the amount of reverb.
If you don't want to add the reverb effect, set it to 0.
Explanation
Type of reverb
Adjusts the delay time from the
direct sound until the reverb
sound is heard.
Adjusts the decay length of the
reverb sound.
Adjusts the density of the reverb
sound.
Adjusts the change in the density
of the reverb over time.
The higher the value, the more
the density increases with time.
(The effect of this setting is most
pronounced with long reverb
times.)
Adjusts the low-frequency
portion of the reverb.
Adjusts the high-frequency
portion of the reverb.
Reverb spread
Tonal character of the reverb
2 Warm Hall
Parameter Value
PreDelay 0–100
Time
0.3–30.0 (sec)
Pre LPF (*3)
Pre HPF
(*4)
PreLoop LPF (*3)
Diffusion
0–127
HF Damp Freq
(*5)
HF Damp Ratio 0.1–1.0
(*3) 16, 20, 25, 32, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400, 500,
630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300,
8000, 10000, 12500, 15000 (Hz), BYPASS
(*4) BYPASS, 16, 20, 25, 32, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315,
400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000,
5000, 6300, 8000, 10000, 12500, 15000 (Hz)
(*5) 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 (Hz)
Scene Parameters
Explanation
Adjusts the delay time from the
direct sound until the reverb
sound is heard.
Adjusts the decay length of the
reverb sound.
Frequency above which to cut
the high-frequency portion of
the sound entering the reverb
Frequency below which to cut
the low-frequency portion of the
sound entering the reverb
Frequency above which to cut
the high-frequency portion of
the extended reverberation
Adjusts the change in the density
of the reverb over time.
Adjusts the frequency above
which to cut the high-frequency
portion of the reverb.
Adjusts the amount by which to
attenuate the high-frequency
portion of the reverb.
31