Od 0 Delay; Ds 0 Delay; Chorus; Space-D - Roland V-Drums TD-27 Data List

Multi-Effect Parameters

OD 0 DELAY

Parameter Value
Overdrive
0–127
Drive
Overdrive Pan
L64–R63
Tempo Sync
OFF, ON
Delay Time
1–2600msec, note
Delay
-98–+98%
Feedback
Delay HF
200–8000Hz,
Damp BYPASS
D100:0W–
Delay Balance
D0:100W
Level
0–127

DS 0 DELAY

The parameters are essentially the same as in "OD0DELAY" with the
exception of the following two.
Overdrive Drive0Distortion Drive, Overdrive Pan0Distortion Pan

CHORUS

This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
Parameter Value
Filter Type
OFF, LPF, HPF
Cutoff Freq
200–8000Hz
Pre Delay
0.0–100.0ms
Tempo Sync
OFF, ON
0.05–10.00Hz,
Rate
note
Depth
0–127
Phase
0–180deg
Low Gain
-15–+15dB
High Gain
-15–+15dB
Level
0–127
44
Explanation
Degree of distortion
Also changes the volume.
Stereo location of the overdrive sound
Specifies whether the delay time value of
the delay is specified as a note value (ON) or
not (OFF).
Adjusts the delay time from the direct sound
until the delay sound is heard.
Adjusts the proportion of the delay sound
that is fed back into the effect. Negative "-"
settings will invert the phase.
Adjusts the frequency above which sound
fed back to the effect will be cut. If you do
not want to cut the high frequencies, set this
parameter to BYPASS.
Adjusts the volume balance between the
sound that is sent through the delay (W)
and the sound that is not sent through the
delay (D).
Output Level
Explanation
Type of filter
OFF: no filter is used
LPF: cuts the frequency range above the
Cutoff Freq
HPF: cuts the frequency range below the
Cutoff Freq
Specifies the frequency at which the filter
cuts a specific frequency region
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Specifies whether the modulation rate is
specified as a note value (ON) or not (OFF).
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Gain of the low range
Gain of the high range
Output Level

SPACE-D

This is a multiple chorus that applies two-phase modulation in stereo.
It gives no impression of modulation, but produces a transparent
chorus effect.
Parameter Value
Pre Delay
0.0–100.0ms
Tempo Sync
OFF, ON
0.05–10.00Hz,
Rate
note
Depth
0–127
Phase
0–180deg
Low Gain
-15–+15dB
High Gain
-15–+15dB
Level
0–127

OD 0 CHORUS

Parameter Value
Overdrive
0–127
Drive
Overdrive Pan
L64–R63
Chorus Pre
0.0–100.0ms
Delay
Tempo Sync
OFF, ON
0.05–10.00Hz,
Rate
note
Chorus Depth
0–127

Chorus

D100:0W–
Balance D0:100W
Level
0–127

DS 0 CHORUS

The parameters are essentially the same as in "OD0CHORUS" with
the exception of the following two.
Overdrive Drive0Distortion Drive, Overdrive Pan0Distortion Pan
Explanation
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Specifies whether the modulation rate is
specified as a note value (ON) or not (OFF).
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Gain of the low range
Gain of the high range
Output Level
Explanation
Degree of distortion
Also changes the volume.
Stereo location of the overdrive sound
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Specifies whether the modulation rate is
specified as a note value (ON) or not (OFF).
Frequency of modulation
Depth of modulation
Adjusts the volume balance between the
sound that is sent through the chorus (W)
and the sound that is not sent through the
chorus (D).
Output Level