Operating Weights - Copper Fin Coils - York MILLENNIUM YCAS Installation Operation & Maintenance

Technical Data
OPERATING WEIGHTS – COPPER FIN COILS
YCAS A B C D
0373 764 691 861 ––
0403 777 700 880 ––
0453 782 708 883 ––
0503 794 717 901 ––
0543 796 633 784 589
0573 803 640 794 591
0623 814 646 803 599
0653 901 732 1060 499
MAX LOAD
ISOLATOR
TYPE & SIZE
lbs.
AWMR-1-53 1000
AWMR-1-530 1150
AWMR-1-531 1276
AWMR-1-532 1500
AWMR-1-551 1676
AWMR-1-552 1900
AWMR-1-553 2200
AWMR-2-531 2552
AWMR-2-532 3000
INSTALLATION INSTRUCTIONS FOR VMC SERIES AWR/AWMR
1. Floor should be level and smooth.
2. For indoor applications, isolators do not normally
require bolting. If necessary, anchor isolators to floor
through bolt holes in base plate. IMPORTANT:
Isolators must be bolted to substructure and
equipment to isolators when used under out-
door equipment exposed to wind forces.
3. Lubricate threads of adjusting bolt. Loosen hold-
down bolts to allow for isolator adjustment.
4. Block the equipment 1/4" higher than the specified
free height of the isolator. To use the isolator as
blocking for the equipment, insert a 1/4" shim be-
tween the upper load plate and vertical uprights.
Lower the equipment on the blocking or shimmed
isolators.
78
COPPER FIN COIL WEIGHT DISTRIBUTION BY MODEL ( KGS )
E F G H
607 745 899 ––
627 757 928 ––
614 754 908 ––
633 767 937 ––
877 615 754 697
867 612 748 689
884 621 762 702
960 681 1147 514
DEFL.
kg in. mm
453.6 2 51
521.6 2 51
578.8 2 51
680.4 2 51
760.2 2 51
861.8 2 51
997.9 2 51
1157.6 2 51
1360.8 2 51
AND CP RESTRAINED MOUNTINGS
I J K L
–– –– –– ––
–– –– –– ––
–– –– –– ––
–– –– –– ––
–– –– –– ––
–– –– –– ––
–– –– –– ––
–– –– –– ––
MAX LOAD
ISOLATOR
TYPE & SIZE
lbs. kg
CP-2-26 1200 544.3
CP-2-27 1500 680.4
CP-2-28 1800 816.4
CP-2-31 2200 997.9
CP-2-32 2600 1179.3
CP-2-35 3000 1360.8
5. Complete piping and fill equipment with water, re-
frigerant, etc.
6. Turn leveling bolt of first isolator four full revolu-
tions and proceed to mount each in turn.
7. Continue turning leveling bolts until equipment is fully
supported by all mountings and equipment is raised
free of the spacer blocks or shims. Remove blocks
or shims.
8. Turn leveling bolt of all mountings in either direction
in order to level the installation.
9. Tighten nuts on hold down bolts to permit a clear-
ance of 1/8" between resilient washer and under-
side of channel cap plate.
10. Installation is now complete.
M N O P TOTAL
–– –– –– ––
4,567
–– –– –– ––
4,668
–– –– –– ––
4,649
–– –– –– ––
4,750
–– –– –– ––
5,745
–– –– –– ––
5,744
–– –– –– ––
5,831
–– –– –– ––
6,494
DEFL.
SPRING
COLOR
in. mm
1.17 29.7 Purple
1.06 26.9 Orange
1.02 25.9 Green
0.83 21.0 Gray
0.74 18.7 White
0.70 17.7 Gold
YORK INTERNATIONAL