Breaking In The Machine; Starting And Shutting Off The Engine - Toro Greensmaster TriFlex 3400 Operator's Manual

slopes are safe for machine operation. Always
use common sense and good judgement when
performing this survey.
•
Slopes are a major factor related to loss-of-control
and tip-over accidents, which can result in severe
injury or death. Operating the machine on any
slope requires extra caution.
•
Operate the machine at a lower speed when you
are on a slope.
•
If you feel uneasy operating the machine on a
slope, do not do it.
•
Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
•
Choose a low ground speed so you will not have
to stop or shift while on a slope.
•
A rollover can occur before the tires lose traction.
•
Avoid operating the machine on wet grass. Tires
may lose traction; regardless if the brakes are
available and functioning.
•
Avoid starting, stopping, or turning the machine
on a slope.
•
Keep all movement on slopes slow and gradual.
Do not suddenly change the speed or direction of
the machine.
•
Do not operate the machine near dropoffs, ditches,
embankments, or bodies of water. The machine
could suddenly roll over if a wheel goes over the
edge or the edge caves in. Establish a safety area
between the machine and any hazard (2 machine
widths).

Breaking in the Machine

Refer to the engine manual supplied with the
machine for oil change and maintenance procedures
recommended during the break-in period.
Only 8 hours of mowing operation is required for the
break-in period.
Since the first hours of operation are critical to future
dependability of the machine, monitor its functions and
performance closely so that minor difficulties, which
could lead to major problems, are noted and can be
corrected. Inspect the machine frequently during
break-in for signs of oil leakage, loose fasteners, or
any other malfunction.
Starting and Shutting Off
the Engine
Note:
Inspect the areas beneath the mowers to be
certain they are clear of debris.
Starting the Engine
Important:
Do not use ether or other types of
starting fluid.
Note:
You may need to bleed the fuel system before
starting the engine if any of the following situations
have occurred:
•
Initial start up of a new engine
•
The engine has ceased running due to lack of fuel.
•
Maintenance has been performed upon fuel
system components; ie. filter replaced, etc.
Refer to your engine owner's manual.
1. Sit on the seat, lock the parking brake,
disengage the raise/lower mow control and
move the functional-control lever to the N
position.
2. Remove your foot from the traction pedal and
make sure the pedal is in the N
3. Move the throttle lever to the S
4. Insert the key into the switch and rotate it to the
O position. Hold it in the O
N
glow-plug-indicator light goes off (approximately
6 seconds).
5. Turn the ignition key to the S
Important:
To prevent overheating of the
starter motor, do not engage the starter
longer than 10 seconds. After 10 seconds of
continuous cranking, wait 60 seconds before
engaging the starter motor again.
6. Release the key when the engine starts and
allow it to move to the O
7. Allow the engine to warm up for a few minutes
before operating.
Important:
When starting the engine for
the first time or after an overhaul of the
engine, operate the machine in forward and
reverse for one to two minutes. Turn the
steering wheel to the left and right to check
the steering response. Then shut the engine
off (see Stopping in Starting and Stopping
the Engine) and wait for all moving parts to
stop. Check for oil leaks, loose parts and
any other noticeable malfunctions.
Shutting Off the Engine
1. Move the throttle lever to the S
disengage the raise/lower mow control, and
move the functional-control lever to the N
position.
2. Rotate the ignition key to the O
shut off the engine. Remove the key from the
switch to prevent accidental starting.
21
EUTRAL
position.
EUTRAL
position.
LOW
position until the
N
position.
TART
position.
N
position,
LOW
EUTRAL
position to
FF