Yamaha 007POTO-G0 Owner's Manual page 68

Signal flow for output channels
■ STEREO channel / MONO (C) channel
Each of these channels process the signal sent from the input channels to the STEREO bus or MONO (C) bus, and
send it to an output port or MATRIX bus. If input channels are set to LCR mode, the STEREO (L/R) channels and
the MONO (C) channel can be used together as a set of three output channels.
When the LS9 is in the initial state, the STEREO channel is assigned to the 2TR OUT DIGITAL jack.
M
O
N
ST MATRIX CUE
MIX
O
1 2 ... ...
(C) 1 2
15 16 L R 7 8 L R
■ MATRIX channels 1–8
These channels process the signals sent from MIX channels and STEREO/MONO channels to MATRIX buses,
and send them to the corresponding output ports.
M
O
N
ST MATRIX CUE
MIX
O
1 2 ... ...
(C) 1 2
15 16 L R 7 8 L R
● ATT (attenuator)
Attenuates/boosts the level of the signal.
● 4 BAND EQ (4 band equalizer)
This is a parametric EQ with four bands; HIGH, HIGH
MID, LOW MID, and LOW.
● COMP/COMPANDER/EXPAND (compressor/com-
pander/expander)
This is a dynamics processor that can be used as a com-
pressor, compander, or expander.
● LEVEL
This adjusts the output level of the channel.
● BALANCE (STEREO channel only)
Adjusts the left/right volume balance of the STEREO (L/
R) channel.
68
LS9-16/32 Owner's Manual
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
STEREO L,R,MONO(C)
To RACKIN PATCH
INSERT POINT
To OUTPUT PATCH
STEREO
PRE FADER INSERT OUT
INSERT OUT L,R,MONO(C)
PRE EQ INSERT OUT
STEREO
INSERT IN L,R,MONO(C)
PRE EQ
METER
INSERT
4BAND
ATT
PRE EQ
PRE EQ
INSERT OUT
CUE ON
MATRIX1,3...7 LEVEL ON
LEVEL
MATRIX2,4...8 ON
LEVEL
ON
PAN
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
MATRIX1-8
To RACKIN PATCH
INSERT POINT
To OUTPUT PATCH
MATRIX
PRE FADER INSERT OUT
INSERT OUT 1-8
PRE EQ INSERT OUT
MATRIX
INSERTIN1-8
PRE EQ
METER
INSERT
4BAND
ATT
PRE EQ
PRE EQ
INSERT OUT
CUE ON
EQ OUT DYNA OUT PRE FADER
METER METER METER
GR METER
LEVEL BAL
COMP
INSERT
COMPAND
EQ
EXPAND
PRE FADER
POST EQ PRE FADER
INSERT OUT
To STEREO OUT L+C,R+C
Keyin
Self PRE EQ/Self POST EQ/MIX13-16 OUT/
ST(L,R,MONO(C)) POST EQ
(PRE FADER)PFL / (POST ON)AFL
To MATRIX
PRE FADER / POST ON
VARI
STEREO OUT MONO(C)
To MATRIX
PRE FADER / POST ON
VARI
STEREO
EQ OUT DYNA OUT PRE FADER
METER METER METER
GR METER
LEVEL
COMP
INSERT
COMPAND
EQ
EXPAND
PRE FADER
PRE FADER
POST EQ
INSERT OUT
Keyin
Self PRE EQ/Self POST EQ/MIX13-16 OUT/
MATRIX1-8 POST EQ
(PRE FADER)PFL / (POST ON)AFL
● ON (on/off)
Turns the output channel on/off. If this is off, the corre-
sponding channel is muted.
● TO MATRIX ON/OFF (MATRIX send on/off)
This is an on/off switch for the signal sent from the MIX
channels, STEREO (L/R) channel, or MONO (C) channel
to each MATRIX bus 1–8.
● TO MATRIX LEVEL 1-8 (MATRIX send levels 1–8)
This adjusts the send level of the signal sent from the MIX
channels, STEREO (L/R) channel, or MONO (C) channel
to each MATRIX bus 1–8. As the position from which the
signal is sent to the MATRIX bus, you can choose either
pre-fader or after the [ON] key.
POST ON
METER
STEREO OUT
ON
L,R,MONO(C)
To OUTPUT PATCH
To MONITOR SELECT
To RECORDER IN PATCH
POST ON
STEREO OUT L+C
STEREO OUT L To OUTPUT PATCH
To RECORDER IN PATCH
STEREO OUT R+C
STEREO OUT R To OUTPUT PATCH
To RECORDER IN PATCH
POST ON
METER
ON
MATRIX OUT 1-8
To OUTPUT PATCH
To MONITOR SELECT
To RECORDER IN PATCH
POST ON