Yamaha 007POTO-G0 Owner's Manual page 241

■ DELAY+REV
One input, two output delay and reverb effects in parallel.
Parameter Range
DELAY L 0.0–1000.0 ms Left channel delay time
DELAY R 0.0–1000.0 ms Right channel delay time
FB. DLY 0.0–1000.0 ms Feedback delay time
Feedback gain (plus values for
FB. GAIN –99 to +99% normal-phase feedback, minus
values for reverse-phase feedback)
Delay high-frequency feedback
DELAY HI 0.1–1.0
ratio
Delay and reverb balance (0% =
DLY/REV 0–100%
all delay, 100% = all reverb)
THRU, 21.2 Hz–
HPF High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
REV HI 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
SYNC OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
NOTE L *1
to determine left channel DELAY L
Used in conjunction with TEMPO
NOTE R to determine right channel DELAY
*1
R
Used in conjunction with TEMPO
NOTE FB
*1
to determine FB. DLY
*1.
(Maximum value depends on the tempo setting)
■ DELAY→REV
One input, two output delay and reverb effects in series.
Description Parameter
DELAY L
DELAY R
FB. DLY
FB. GAIN
DELAY HI
DLY.BAL
HPF
LPF
REV TIME
INI. DLY
REV HI
DIFF.
DENSITY
SYNC
NOTE L
NOTE R
NOTE FB
*1.
■ DIST→DELAY
One input, two output distortion and delay effects in series.
Parameter
DST TYPE
DRIVE
MASTER
TONE
N. GATE
SYNC
DLY.NOTE
MOD.NOT
E
DELAY
FB. GAIN
HI. RATIO
FREQ.
DEPTH
DLY.BAL
*1.
*2.
Range
0.0–1000.0 ms Left channel delay time
0.0–1000.0 ms Right channel delay time
0.0–1000.0 ms Feedback delay time
Feedback gain (plus values for
–99 to +99% normal-phase feedback, minus
values for reverse-phase feedback)
Delay high-frequency feedback
0.1–1.0
ratio
Delay and delayed reverb balance
0–100% (0% = all delayed reverb, 100% =
all delay)
THRU, 21.2 Hz–
High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
0.3–99.0 s Reverb time
0.0–500.0 ms Initial delay before reverb begins
0.1–1.0 High-frequency reverb time ratio
0–10 Spread
0–100% Reverb density
OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*1
to determine left channel DELAY L
Used in conjunction with TEMPO
to determine right channel DELAY
*1
R
Used in conjunction with TEMPO
*1
to determine FB. DLY
(Maximum value depends on the tempo setting)
Range
DST1, DST2, OVD1, Distortion type (DST = distortion,
OVD2, CRUNCH OVD = overdrive)
0–100 Distortion drive
0–100 Master volume
–10 to +10 Tone control
0–20 Noise reduction
OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*1
to determine DELAY
Used in conjunction with TEMPO
*2
to determine FREQ.
0.0–2725.0 ms Delay time
Feedback gain (plus values for
normal-phase feedback, minus
–99 to +99%
values for reverse-phase feed-
back)
0.1–1.0 High-frequency feedback ratio
0.05–40.00 Hz Modulation speed
0–100% Modulation depth
Distortion and delay balance (0%
0–100% = all distortion, 100% = all
delayed distortion)
(Maximum value depends on the tempo setting)
LS9-16/32 Owner's Manual
Effects Parameters
Description
Description
241