1. Manuals
  2. Brands
  3. Vision Fitness Manuals
  4. Fitness Equipment
  5. ST200
  6. Assembly manual

Vision Fitness ST200 Assembly Manual

Functional trainer
Hide thumbs Also See for ST200:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
A s s e m b l y
G u i d e
ST200
FUNCTIONAL TRAINER

Advertisement

Table of Contents
loading

Related Manuals for Vision Fitness ST200

Summary of Contents for Vision Fitness ST200

  • Page 1 A s s e m b l y G u i d e ST200 FUNCTIONAL TRAINER...
  • Page 2 A s s e m b l y G u i d e ST200 FUNCTIONAL TRAINER To avoid possible damage to this Functional Trainer, please follow these assembly steps in the correct order. Before proceeding, find your new Functional Trainer serial number located on the back of the rear floor support (1a), and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records.
  • Page 3 STEP STEP STEP STEP STEP STEP STEP STEP STEP...
  • Page 4 TOOLS & PARTS INCLUDED 10mm/17mm Wrench 19mm Wrench 4mm L-Shaped Wrench 6mm L-Shaped Wrench PARTS BOX Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card...
  • Page 5 HARDWARE INCLUDED ORANGE BAG 10.5 x 18 x 2T SW10.2 x 18.4 x 2.5T M10 x 1.5P Nut 10.5 x 30 x 2T Flat Washer Spring Washer Quantity: 6 Flat Washer Quantity: 8 Quantity: 4 Quantity: 4 M10 x 1.5P x 60L Bolt M10 x 1.5P x 25L Bolt Quantity: 4 Quantity: 2...
  • Page 6 HARDWARE INCLUDED PINK BAG M10 x 1.5P Nut 10.5 x 18 x 2T M10 x 1.5P x 25L Bolt Quantity: 2 Flat Washer Quantity: 8 Quantity: 2 M10 x 1.5P x 60L Bolt Quantity: 2 GREEN BAG 10.5 x 18 x 2T SW10.2 x 18.4 x 2.5T M10 x 1.5P Nut Flat Washer...
  • Page 7 HARDWARE INCLUDED BLACK BAG 6.4 x 14 x 1T M6 x 1P Nut SW6.1 x 12.2 x 1.5T M10 x 1.5P x 60L Bolt Flat Washer Quantity: 2 Spring Washer Quantity: 2 Quantity: 2 Quantity: 2 M6 x 1P x 50L Bolt 10.5 x 18 x 2T SW10.2 x 18.4 x 2.5T M10 x 1.5P Nut...
  • Page 8 HARDWARE INCLUDED RED BAG M10 x 1.5P x 25L Bolt SW10.2 x 18.4 x 2.5T Quantity: 10 Spring Washer Quantity: 10...
  • Page 9 ORANGE BAG STEP • Lay the back side of the rear vertical upright (1a) down onto the floor. The threaded bolt ends will be pointing up. Place the center floor support (1b) over the threaded ends. Attach a flat (10.5x18x2T) and spring (SW10.2x18.4x2.5T) washer and nut (M10x1.5P) to each end.
  • Page 10 BLUE BAG STEP • Thread pull pins partially onto 2a (Qty. 1) and 2c (Qty. 2). • Lay the front center vertical (2f) on the floor. Slide the seat support structure (2a) over the open end of 2f. NOTE: You must pull the pull pin out (2b) and hold it when sliding over 2f.
  • Page 11 Notch is in front STEP PINK BAG • Place the top front structure (3a) on top of 2f and attach with two bolts (M10x1.5Px60L), two flat (10.5x18x2T) washers, and two nuts (M10x1.5P). Tighten fasteners with a 6mm L-shaped wrench and a 17mm wrench. •...
  • Page 12 GREEN BAG STEP • Place the bottom of the left oval upright (4a) onto the protruding bolts of 1d. NOTE: Make sure the 27 holes of 4a are on the outside. Mate the hole in the top of 4a with the top hole of 3a. Attach and tighten one flat (10x30x2T) &...
  • Page 13 BLACK BAG STEP • If you are adding 15 weight plates to the base unit, proceed as follows. If you are adding 20 weight plates, the steel tube spacer (5a) will not be used. • Place two rubber weight plate bumpers (5b) over the 0.75”...
  • Page 14 YELLOW BAG STEP Wrap one end of cable #1 around pulley A. On the right side of the unit, place it through pulleys B, C, D of 6a, and E. Remove the nuts from 2 slotted bolts (M12) (see diagram below). With the threads pointing down on the slotted bolt (M12), slide the end of cable #1 through it.
  • Page 15 YELLOW BAG STEP If assembling just the base unit (ST200), proceed as follows. If assembling with the leg press (ST250), refer to Step 5 of the leg press assembly guide. Slide the small steel end of cable #2 through pulleys F and G.
  • Page 16 YELLOW BAG STEP PULLEY H through PULLEY M • Remove the slotted bolts (8a) located on the inside of the right and left handles of uprights 4a & 4b. Remove the nuts from the bolts. Slide the small steel end of cable Cable #3 #3 through pulleys H &...
  • Page 17 RED BAG STEP • Place the rear hole of the left decorative cover (9a) over the threaded post on the left side of structure 5e. Loosely attach a spring (SW10.2x18.4x2.5T) washer and a bolt (M10x1.5Px25L). Thread two bolts (M10x1.5Px25L) spring (SW10.2x18.4x2.5T) washers into the two front holes.
  • Page 18 DECALS STEP • Attach the decals according to the diagram below. General Warning/Safety Decal Placement Weight Plate Sticker Placement...
  • Page 20 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 www.visionfitness.com ©2005 Vision Fitness. All Rights Reserved. 10.05 AG18.37PRD REV2...

Table of Contents