Extron electronics ISS 608 User Manual page 63

Command
Advanced Configuration (continued)
HDCP notification (Green screen/message)
Enable Notification
Query Notification
X4&
KEY: = HDCP notification mode
HDCP status
Query input
Query output
X!
KEY: = Input number
X@
= Output selection
X4$
= HDCP status
Video signal presence
View video signal presence
X6!
KEY: = Video signal status
Resets
NOTE: The factory configured passwords for all accounts on this device have been set to the device serial number. In the event of a complete
system reset, the passwords convert to the default, which is no password (see
Soft reset
Absolute system reset
Absolute system reset
retain IP
Serial port configuration
Set serial port parameters
Query software version
X3!
KEY: = Baud rate of port
X3@
= Parity
X3#
= Data bits
X3$
= Stop bits
Backup and restore configuration
Save unit configuration
Restore unit configuration
X3%
KEY: = Configuration type
ASCII (Telnet)
(host to switcher)
E X4& }
N1* HDCP
E }
N1HDCP
0
= Black screen/notification disabled (Mute output)
2
= User file with black screen
E X! }
I HDCP
Verbose mode 2/3
E X@ }
O HDCP
Verbose mode 2/3
1
– 8 (two-digit response with
1 2
= Preview = Program
0
= No sink or source device detected
2
= Sink or source detected with HDCP
E }
0 LS
Verbose mode 2/3
0
= Video/TMDS signal not detected
E }
ZXXX
E }
ZQQQ
E }
ZY
E X3! X3@ X3# X3$ }
1* CP
, , ,
E
1CP
Verbose mode 2/3
300 600 1200 1800 2400
, , , ,
115200
O E N M
dd, ven, one (Default), ark,
7 8
or (Default)
1 2
(Default) or
E X3% }
1* XF
E X3% }
0* XF
0
= IP configuration (ip.cfg)
Response
(switcher to host)
X4&]
HdcpN1*
X4&]
X4$]
X! X4$]
HdcpI *
X4$]
X@ X4$]
HdcpO *
0
padding)
1
= Sink or source detected but no HDCP
X6! X6! X6! ]
* *... *
• X6! X6! ]
In00 *... *
1
= Video/TMDS signal detected
Passwords on page 57 to change a password).
]
Zpx
]
Zpq
]
Zpy
X3! X3@ X3# X3$]
Cpn1•Ccp , , ,
X3! X3@ X3# X3$]
, , ,
X3! X3@ X3# X3$]
Cpn1•Ccp , , ,
3600 4800 7200 9600
, , , , (Default),
S
pace (only the first letter is required)
X3%]
Cfg1*
X3%]
Cfg0*
2
= Unit-specific parameters (box.cfg)
ISS 608 Seamless Switcher • SIS Configuration and Control
Additional description
Enable the HDCP notification
Query the HDCP notification
1
= Green screen (Default)
Query the HDCP status of input
Query the HDCP status of output
X@
IN#1 ... IN#8
Reset all device settings to factory
default
Reset all device and IP settings to
factory default
Same as absolute system reset
except that IP address, subnet
mask, gateway address, DHCP,
and port mapping are not reset
Set the RS-232 port parameters
View port parameters
X3! X3@ X3# X3$
, , , and
232 port
14400 19200 28800 38400
, , , ,
Back up the current unit
X3%
configuration as type
on the ISS
Restore the saved configuration,
X3%
type
X!
of the RS-
57600
,
to a file
55