Siemens SINAMICS G120C Getting Started page 36

Commissioning
4.2 Further settings
P-No. Note
p1310 Voltage boost permanent [100 % ≙ p0305]
p1311 Voltage boost when accelerating [%]
p1312 Voltage boost when starting [%]
r1315 Voltage boost, total [100 % ≙ p2001]
p1320 V/f control programmable characteristic frequency
1 [Hz]
p1321 V/f control programmable characteristic voltage 1
[V]
p1322 Characteristic frequency 2 [Hz]
p1323 Characteristic voltage 2 [V]
p1324 Characteristic frequency 3 [Hz]
p1325 Characteristic voltage 3 [V]
p1326 Characteristic frequency 4 [Hz]
p1327 Characteristic voltage 4 [V]
p1330 CI: V/f control independent voltage setpoint
[100 % ≙ p2001]
p1334 V/f control slip compensation starting frequency
[Hz]
p1335 Slip compensation, scaling [100 % ≙ r0330]
p1336 Slip compensation limit value [100 % ≙ r0330]
r1337 CO: Actual slip compensation [100 ≙ 100%]
p1338 V/f mode resonance damping gain
34
P-No. Note
p1340 I frequency controller proportional gain
max
p1341 I frequency controller integral time [s]
max
r1343 CO: I_max controller frequency output
[100 % ≙ p2000]
p1349 U/f mode resonance damping maximum
frequency [Hz]
p1351 CO: Motor holding brake starting frequency
[100 ≙ 100%]
p1352 CI: Motor holding brake starting frequency
[100 ≙ 100%]
r1438 CO: Speed controller speed setpoint
[100 % ≙ p2000]
p1452 Speed controller speed actual value smoothing
time (SLVC) [ms]
p1470 Speed controller encoderless operation P gain
p1472 Speed controller sensorless operation integral
time [ms]
p1475 CI: Speed controller torque setting value for motor
holding brake [100 % ≙ p2003]
r1482 CO: Speed controller I torque output
[100 % ≙ p2003]
r1493 CO: Moment of inertia, total
p1496 Acceleration pre-control scaling [%]
p1511 CI: Supplementary torque 1 [100 % ≙ p2003]
r1516 CO: Supplementary torque and acceleration
torque [100 % ≙ p2003]
p1520 CO: Torque limit upper [Nm]
p1521 CO: Torque limit lower [Nm]
p1522 CI: Torque limit upper [100 % ≙ p2003]
p1523 CI: Torque limit lower [100 % ≙ p2003]
p1524 CO: Torque limit upper/motoring scaling
[100 ≙ 100%]
p1525 CO: Torque limit lower scaling [100 ≙ 100%]
r1526 CO: Torque limit upper without offset
[100 % ≙ p2003]
r1527 CO: Torque limit lower without offset
[100 % ≙ p2003]
p1530 Power limit motoring [kW]
p1531 Power limit regenerative [kW]
r1538 CO: Upper effective torque limit [100 % ≙ p2003]
r1539 CO: Lower effective torque limit [100 % ≙ p2003]
r1547 CO: Torque limit for speed controller output
[0] Upper limit [100 % ≙ p2003]
Getting Started, 03/2012, FW V4.5, A5E03831830B AA
SINAMICS G120C frequency converter