Parameter List - Siemens SINAMICS G120C Getting Started

4.2.3

Parameter list

The following list contains the basic parameter
information with access level 1 ... 3. The complete
parameter list is provided in the list manual, see
Product support (Page 49).
P-No. Note
r0002 Drive operating display
p0003 Access level
p0010 Drive, commissioning parameter filter
p0015 Macro drive unit
See also Pre-defined interface configurations
(Page 14).
r0018 Control Unit firmware version
r0020 Speed setpoint smoothed [100 % ≙ p2000]
r0021 CO: Actual speed smoothed [100 % ≙ p2000]
r0022 Speed actual value rpm smoothed [rpm]
r0024 Output frequency smoothed [100 % ≙ p2000]
r0025 CO: Output voltage smoothed [100 % ≙ p2001]
r0026 CO: DC link voltage smoothed [100 % ≙ p2001]
r0027 CO: Absolute actual current smoothed
[100 % ≙ p2002]
r0031 Actual torque smoothed [100 % ≙ p2003]
r0032 CO: Active power actual value smoothed
[100 % ≙ r2004]
r0034 Motor utilization [100 ≙ 100%]
r0035 CO: Motor temperature [100°C ≙ p2006]
r0036 CO: Power unit overload I
r0039 Energy consumption
p0040 0 → 1 Reset the energy consumption display
r0041 Energy usage saved/energy saved
p0045 Smoothing time constant, display values [ms]
r0046 CO/BO: Missing enable signals
r0047 Motor data identification routine and speed
controller optimization
r0050 CO/BO: Command Data Set CDS effective
r0051 CO/BO: Drive Data Set DDS effective
r0052 CO/BO: Status word 1
.00 Ready to start
.01 Ready
.02 Operation enabled
.03 Fault active
.04 Coast down active (OFF2)
SINAMICS G120C frequency converter
Getting Started, 03/2012, FW V4.5, A5E03831830B AA
t [100 ≙ 100%]
2
P-No. Note
.05 Quick stop active (OFF3)
.06 Closing lockout active
.07 Alarm active
.08 Deviation, setpoint/actual speed
.09 Control requested
.10 Maximum speed reached
.11 I,M,P limit reached
.12 Motor holding brake open
.13 Alarm overtemperature motor
.14 Motor rotates forwards
.15 Alarm inverter overload
r0053 CO/BO: Status word 2
r0054 CO/BO: Control word 1
.00 ON/OFF1
.01 OFF2
.02 OFF3
.03 Enable ramp-function generator
.04 Enable ramp-function generator
.05 Continue ramp-function generator
.06 Enable speed setpoint
.07 Acknowledge fault
.08 Jog bit 0
.09 Jog bit 1
.10 Master control by PLC
.11 Direction reversal (setpoint)
.13 Motorized potentiometer, raise
.14 Motorized potentiometer, lower
.15 CDS bit 0
r0055 CO/BO: Supplementary control word
.00 Fixed setpoint, bit 0
.01 Fixed setpoint, bit 1
.02 Fixed setpoint, bit 2
.03 Fixed setpoint, bit 3
.04 DDS selection, bit 0
.05 DDS selection, bit 1
.08 Technology controller enable
.09 DC braking enable
.11 Droop enable
.12 Closed-loop torque control active
.13 External fault 1 (F07860)
.15 CDS bit 1
r0056 CO/BO: Status word, closed-loop control
27