Rear Panel; (Connecting Your Equipment) - Roland FANTOM Series Reference Manual

Panel Descriptions

Rear Panel

(Connecting Your Equipment)

MIDI device
104
page
A
to Power outlet Power cord
Pedal unit
(RPU-3)
* To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.
A
Power Supply
Controller Explanation
[L] switch This turns the power on/off .
Connect the included power cord to this connector .
AC IN jack * To prevent malfunction and equipment failure, always turn
B
OUTPUT jack
Controller Explanation
You can connect a set of headphones here .
PHONES jack
Even if headphones are connected, an audio signal is
sent from the OUTPUT jacks and BALANCED OUT jacks .
These are balanced output jacks for audio signals .
Connect them to your mixer .
MAIN OUT jacks
TIP: HOT (L, R)
2: HOT 1: GND 1: GND
RING: (Balanced) COLD
SLEEVE: GND
3: COLD
These are output jacks for audio signals . Connect them
MAIN OUT jacks
to your amp . If you're outputting in mono, connect the
(L/MONO, R)
L/MONO jack .
SUB OUT 1 jacks
(L, R)
These are output jacks for sub-out audio .
SUB OUT 2 jacks
(L, R)
These output the sound that has passed through the
ANALOG FILTER OUT
jacks
analog filter section .
(1, 2)
C
CV/GATE jacks
Controller Explanation
These jacks output note-on/off . They output +5 V .
GATE OUT jacks
Depending on the settings, GATE OUT 2 can also be
(1, 2)
used as CV OUT .
These jacks output pitch . If you've specified a transpose
or octave shift setting, the voltage changes according
CV OUT jacks
(1, 2)
to the setting .
These jacks support OCT/V (Hz/V is not supported) .
10
Pin assignment of MIC/LINE INPUT jack
TIP: HOT
2: HOT 1: GND
RING: COLD
SLEEVE: GND
3: COLD
Microphone Synthesizer
F E
Expression pedal (EV-5)
or Pedal switch (DP Series)
down the volume, and turn off all the units before making any
connections.
Pin assignment of MAIN
2: HOT
OUT jack
3: COLD
Computer USB flash drive
1: GND 2: HOT
3: COLD
102
page
D G
D
INPUT jack
Controller
MIC/LINE INPUT jacks
(1, 2) (Balanced)
LEVEL knobs
(1, 2)
E
FOOT PEDAL jack
Controller
PEDAL jacks
(CTRL 1, CTRL 2/L,
CTRL 3/C, HOLD/R)
F
MIDI jack
Controller
MIDI connectors
OUT 2/THRU)
G
USB port
Controller
USB MEMORY port
USB COMPUTER port
EXTERNAL DEVICE jacks
(1, 2, 3)
Monitor speakers (powered)
C
External USB device Analog synthesizers or Eurorack
modules that are equipped with
CV/gate input jacks .
Explanation
Connect a mic, audio device, or external synthesizer
etc . to these jacks .
The MIC/LINE INPUT jacks support XLR-type and TRS-
type plugs . The XLR-type connections support 48 V
phantom power, allowing you to connect condenser
mics that use phantom power (phantom power supply:
DC 48 V, 10 mA Max) . Stereo input via a TRS plug is not
supported .
Adjusts the input level of the MIC
INPUT jack .
Explanation
If you connect a pedal switch (sold separately: DP
series) to the HOLD/R jack, you can use it as a damper
pedal . You can also assign various functions to the
pedals that are connected to the CTRL 1, CTRL 2/L, and
CTRL 3/C jacks .
* Use only the specified expression pedal. By connecting any
other expression pedals, you risk causing malfunction and/or
damage to the unit.
Explanation
Used for connecting external MIDI devices and for
transmission of MIDI messages .
(IN, OUT 1,
The OUT 2/THRU connector's function can be switched
to operate either as MIDI THRU or as MIDI OUT .
Explanation
Use a commercially available USB flash drive . However,
we cannot guarantee that all commercially available
USB flash drives will work .
Connect this to your computer to transfer performance
data and audio signals .
Connect these to an external USB device .
Headphones
B
105
page
MAX MIN