Related Manuals for NCR RealPOS 70XRT
Summary of Contents for NCR RealPOS 70XRT
- Page 1 7403-K300 NCR RealPOS 70 (7403) GMS Integration Tray Kit Instructions 26309 Issue A...
-
Page 3: Revision Record
Revision Record Issue Date Remarks Nov 2008 First issue... - Page 5 Introduction The Peripheral Integration Tray kit provides the necessary components for integrating a printer and keyboard with the RealPOS 70 or RealPOS 72 terminal. It can be mounted on a flat surface or on a cash drawer. 26323...
- Page 6 Components 7459 Printer Skirt 497-0451793 (CG1) 7403 Integration Tray Adapter 497-0460475 Compact Alpha w/MSR Filler 497-0451797 (CG1) 7459 Compact Alpha Filler 497-0451848 (CG1) Integration Tray 497-0451781 (CG1) Integration Tray Plug 497-0459016 (CG1) Screw, 8-32 x 0,375, PH, Phillips 006-8611339 Tray Support Bracket 497-0451821 26313...
-
Page 7: Installation Procedures
Installation Procedures The Integration Tray can be installed on an NCR 2181 Cash Drawer or it can be installed directly to a flat surface. The installation procedures are identical except for including the cash drawer. Installing on a Cash Drawer 1. - Page 8 2. Position the Integration Tray on top of the Tray Support Bracket and secure it with screws (4). 26315...
- Page 9 Installing on a Flat Surface 1. Position the Tray Support Bracket on mounting surface and secure it with screws (4) that are appropriate for the surface type. 24611...
- Page 10 2. Position the Integration Tray on top of the Tray Support Bracket. Secure the tray to the Tray Support Bracket with screws (2). Secure the front of the tray to the mounting surface with screws (2) that are appropriate for the surface type. 24613...
-
Page 11: Installing The Keyboard
Note: If a keyboard is not used insert the Integration Tray Plug into the opening where the keyboard cable would normally be routed. 1. Install the keyboard in the Integration Tray. 2. Route the cable as shown. NCR 5932-5xxx USB Alphanumeric Big ticket Keyboard 26316... - Page 12 Compact Keyboard: Install the Keyboard Tray Insert beside the keyboard. Note: There are two Keyboard Tray Inserts. The narrow tray is used in all cases except when using the 5932-65xx PS/2 model without an MSR. Narrow Insert - Use with 5932-6xxx Compact Keyboard w/MSR Wide Insert - Use with 5932-6xxx Compact Keyboard w/o MSR 5932-22xx 64-Key POS Keyboard 5932-65xx PS/2 Compact Alpha-Numeric...
-
Page 13: Installing The Transaction Printer
Installing the Transaction Printer The NCR 7167, 7168, 7197, or 7198 printer can be located on either side of the Integration Tray. Note: The Printer Cable Strain Relief is different on the Release 1.0 and the Series II printers. The Cable Strain Relief on Release 1.0 printers prevents the printer from sitting properly in the Integration Tray and must be removed from the printer and installed in the Integration Tray. - Page 14 3. Connect the Printer Cable to the USB and Power connectors. 4. Series II Printers Only: Route the cable through the Cable Strain Relief on the printer as shown. 33279a...
- Page 15 5. Route the printer cable(s) through the openings in the Integration Tray as shown below and set the printer in the tray opening. NCR 7197/7198 Only: Install the 7459-K316 Printer Skirt (included with 7403-K300). NCR 7167/7168 Only: Secure the cable in the Cable Strain Relief as shown. 7197/7198 Printer 7459-K316 Printer Skirt...
-
Page 16: Installing The Terminal
Installing the Terminal 1. Install the 7403 Integration Tray Adapter. It can be located on either side of the tray. Consideration should be given to the total integrated terminal configuration to obtain satisfactory clearances. Secure the adapter to the Tray Support Bracket with screws (4). - Page 17 2. Place the 7403 terminal on the 7403 Integration Tray Adapter. 26321...
- Page 18 Connecting the External Cables to the Terminal 1. Tilt the Display Module. 26031 2. Remove the Front Cover. a. Insert the Security Key and turn it 90 degrees clockwise. Security Key Front Cover 26124...
- Page 19 b. Pivot the top of the Front Cover toward the front of the unit and remove it from the terminal. 26032...
- Page 20 Connector I/O Panel 1. Connect the printer and LAN cables to the I/O panel. Line Out Cash Drawer RS232/C RS232/D RS232/A RS232/B 26297a...
- Page 21 Printer Cable Connections The printers can connect through a USB connector or an RS-232 connector. It receives power through a Powered USB power cable. USB Installation Connect the Powered USB Printer Interface Cable to the USB Connector and Power Connector on the printer and to the 24 V Powered USB Connector on the terminal. Line Out Cash Drawer...
- Page 22 RS-232 Installation w/Power from Powered USB 1. Connect the RS-232 Printer Interface Cable to the RS-232 Connector on the printer and to an RS-232 Connector on the terminal. 2. Connect the Printer Power Cable to the Power Connector on the printer and to the 24 V Powered USB Connector on the terminal.
- Page 23 Cash Drawer Cable Connections The Cash Drawer can be installed remotely or integrated with the terminal. It can be connected to the Cash Drawer connector on the terminal or to the transaction printer Cash Drawer Kickout. Line Out Cash Drawer RS232/C RS232/D RS232/A...
- Page 24 Second Cash Drawer Cable Connection The terminal supports a 2-drawer configuration with a Y-cable (1416-C372-0006). Connect the Y-cable to the terminal or transaction printer cash drawer connector. Line Out Cash Drawer RS232/C RS232/D RS232/A RS232/B Cash Drawer Connectors 26326...
-
Page 25: Ac Power Cord Connection
AC Power Cord Connection 1. Attach the Power Cord to the system and to an AC power source. AC Power Cord 26135... -
Page 26: Cable Routing
Cable Routing The cables are routed under the base and out the rear of the unit. There are two ways to secure the cables. Terminal Configured with a DVD-ROM Drive If configured with a DVD the cables are routed in the two channels in the bottom of the Base. - Page 27 Terminal without a DVD-ROM Drive If there is no DVD present then there is an additional Cable Clamp on the front of the Base chassis that is used to secure the cables. 1. Loosen the Cable Clamp Thumbscrew 2. Pivot the clamp away from the terminal. Cable Clamp Thumbscrew 26236 3.
- Page 28 External Cable Routing The cables are routed out the back of the terminal and down through the Integration Tray and cash drawer, if applicable. 26328...