Tyres And Mounting; Trouble-Shooting; Maintenance And Care - Sunrise Medical Breezy BasiX Directions For Use Manual

Tyres and Mounting

Tyres and Mounting
Solid tyres are standard.
With pneumatic tyres make sure you that you maintain the correct
tyre pressure, as this can have an effect on wheelchair performance.
If the tire pressure is too low, rolling resistance will increase,
requiring more effort to move the chair forward. Low tyre pressure
also has a negative impact on manoeuvrability. If the tyre pressure
is too high, the tyre could burst. The correct pressure for a given tyre
is printed on the surface of the tyre itself.
Tyres can be mounted the same way as an ordinary bicycle tyre.
Before installing a new inner tube, you should always make sure
that the base of the rim and the interior of the tyre are free of foreign
objects. Check the pressure after mounting or repairing a tyre. It is
critical to your safety and to the wheelchair's performance that
regulation air pressure be maintained and that tyres be in good
condition.

Maintenance and care

Maintenance
• Check the tyre pressure every 4 weeks. Check all tyres for wear
and damage.
• Check the brakes approximately every 4 weeks to make sure that
they are working properly and easy to use.
• Change tyres as you would an ordinary bicycle tyre.
• All of the joints that are critical to safe using your wheelchair
safely are self-locking nuts. Please check every three months to
make sure that all bolts are secure (see the section on torque).
Safety nuts should only be used once and should be replaced
after use.
• Please use only mild household cleansers when your wheelchair
is dirty. Use only soap and water when cleaning the seat
upholstery.
• If your wheelchair should ever get wet, please dry it after use.
• A small amount of sewing-machine oil should be applied to quick-
release axles approximately every 8 weeks. Depending on the
frequency and type of use, we recommend taking your wheelchair
to your authorised dealer every 6 months to have it inspected by
trained personnel.
CAUTION:
Sand and sea water (or salt in the winter) can damage the
bearings of the front and rear wheels. Clean the wheelchair
thoroughly after exposure.
The following parts can be removed and send to the manufacturer /
dealer for repair:
• Rear wheels
• Armrest
• Hanger
• Anti - tips
This components are available as spares. More details can be found
in the party manual.
Hygiene when being reused:
When the chair is to be reused, it should be prepared carefully, and
be wiped and treated with spray disinfectant on all surefaces which
could come into contact with the user.
In doing this, you must use a disinfectant taken from the DGHM
list, e.g. Antifect Liquid (Schülke&Mayr) for alcoholic quick disinfec-
tion for medical products and medical inventory when you require a
quick effect.
Please pay attention to the manufacturer`s instructions of the disin-
fectant you are using.
In general, a safe disinfectant cannot be gueranteed on seams. We
therefore recommend, that you properly dispose of seat and back
slings in the case of microbacterial contamination with active agents
according to § 6 infection protection law.
0806/1/ST-000690646.EMS
Trouble Shooting
Wheelchair pulls to one side
• Check tyre pressure
• Check to make sure wheel turns easily (bearings, axle)
• Check the castor angle
• Check to make sure both castors are making proper contact with
the ground
Castors begin to wobble
• Check the castor angle
• - Check to make sure all bolts are secure; tighten if necessary
(see the section on torque)
• Check to make sure both castors are making proper contact with
the ground
Wheelchair / Cross-tube assembly does not snap into position
in the seat saddle
• Chair is still new, i.e., the seat or backrest upholstery is still very
stiff. This will improve with time.
Wheelchair is difficult to fold up
• Adjustable backrest upholstery is too stiff. Loosen it accordingly.
Wheelchair squeaks and rattles
• - Check to make sure all bolts are secure; tighten if necessary
(see the section on torque)
• Apply small amount of lubrication to spots where movable parts
come in contact with one another
Wheelchair begins to wobble
• Check angle at which castors are set
• Check tyre pressure
• Check to see if rear wheels are adjusted differently
Disposal / recycling of materials
If the wheelchair has been supplied to you
free of charge it may not belong to you. If it is
no longer required follow any instructions
given by the organisation issuing the wheel
chair in order that it may be returned to them.
The following information describes the materials used in the
wheelchair in relation to their disposal or re-cycling of the wheelchair
and its packaging.
Specific waste disposal or recycling regulations may be in force
locally and these should be taken into consideration when disposal
arrangements are made. (This may include the cleaning or de-
contamination of the wheelchair before disposal.)
Aluminium: Castor forks, wheels, side frames, armrests frame, leg
rests, push handles
Steel: Fasteners, QR axle
Plastic: Handgrips, tube plugs, castor wheels, footplates, armpads
and 12" wheel/tyre
Packaging: Low density polythene bag, cardboard box
Upholstery: Woven polyester with PVC coatings and expanded
combustion modified foam.
Disposal or recycling should be done through a licensed agent or
authorised place of disposal. Alternatively your wheelchair may be
returned to your dealer for disposal.
14
BasiX, RubiX, RubiX XL Rev. 1