Menu Features And Programming Instructions - Jacuzzi J-300 Series Installation Manual And Use & Maintenance

Hide thumbs Also See for J-300 Series:

Installation manual and use & maintenance (80 pages)

Installation, use & maintenance manual (76 pages)

Instructions for preinstallation (48 pages)

Table of Contents

Available languages

Enlarged version

Press again

Solid Colour Mode:

Selects one of 7 solid colours of choice.

Pressing the button again will make the sequence starts

from the beginning.

Jets

The water flow through individual jets in your spa can be

adjusted or turned off by rotating the outside jet ring. Some jets

offer an adjustable center nozzle that allows you to change the

water discharge angle. Simply tilt the center nozzle in these jets

to the desired angle to customize your personal massage. Other

jets offer a spiral action that produces a surging stream of air

and water that provides a vigorous massage.

Note: Always keep at least 6 adjustable jets open at all times to en-

sure proper filtration characteristics within the spa.

Selecting Desired Massage Action

All models incorporate a massage selector valve that

allows you to customize the massage and performance by di-

verting water between various jet systems within the spa. Sim-

ply turn valve to positions A, B or C to divert water pressure to

various jet groups.

Note: The valve is intended to operate in positions A (Combo), B,

or C for optimum performance. It is considered normal for sound

levels within the valve to increase between these positions due to

the large amounts of water flowing through it. For optimum filtra-

tion benefits, always leave this valve in position A when the spa is

covered and select positions B or C for maximum jet performance

during spa use.

Waterfall Feature

The waterfall feature allows you to independently control it for a

customized soothing effect. The waterfall is on when the circu-

lation pump is on. The JETS 1 (

will also activate the waterfall feature.

Waterfall Operation Details:

A. Push thumb wheel on top of waterfall to the left (while in spa)

to start or increase flow.

B. Push thumb wheel on top of waterfall to the right (while in

spa) to slow or turn flow off.

NOTE: When the waterfall is in the OFF position, some water

may still flow through. This is considered normal.

CLEARRAY on Demand

The CLEARRAY on demand feature activates the water purifica-

tion system for a period of 1-hour. Press the button to turn the

system on. During this time the circulation pump and the CLE-

ARRAY unit are on.

Note: When the CLEARRAY system is on, due to a programmed

or scheduled setting, the feature cannot be turned off.

) or CLEARRAY (

) buttons

Air Controls

Certain jet systems have their own "toggle" on/off air control.

Each control introduces air into the water lines that supply spe-

cific jet groups. Simply press any air control button Jacuzzi logo

side down to open or press the opposite side of button to close.

Note: To minimize heat loss, close all air controls (Jacuzzi logo

up) when spa is not in use. Certain jets may draw air even thou-

gh they are closed. This is considered normal.

Optional BLUEWAVE® Spa Stereo System

Spas equipped with the optional audio system offer enhanced

enjoyment. These models include a high-quality FM/USB/AUX/

Bluetooth stereo receiver with four high-quality marine spea-

kers for unsurpassed sound quality and long-life.

Note: Digital rights management (DRM) files cannot be played.

Personal files (MP3, WMA, iTunes or AAC) can be played as long as

they are not DRM encrypted files.

Blow-Out Cycle

This cycle will purge the air from the plumbing lines normally

caused by draining and filling the spa. The Jets Pump 1 and the

Circulation Pump will turn on for 1 minute and then shut off.

Then Jets Pump 2 will turn on and run for 1 minute then shut off.

This cycle will only occur at start up.

Note: Turning off the corresponding jets pump that is running can

deactivate the feature.

Cleanup Cycle

The cleanup cycle occurs once per day at 12:00 PM (noon) for 2

minutes. This is not user programmable. The Jets Pump 1 and the

Circulation Pump will turn on for one minute and then shut off.

Then Jets Pump 2 will turn on and run for 1 minute then shut off.

Note: Turning off the corresponding jets pump that is running can

deactivate the feature.