Jacuzzi J-300 Series Installation Manual And Use & Maintenance page 41

LINK"). Press the button again to activate the stereo unit (remote
LCD display will read "WELCOME").
Operating the Radio:
Turn power "ON" to the stereo unit. Press the power button on
the remote.
The LCD screen on the remote will display the following: "Welco-
me, " "Load, " "Radio" and the station number.
You can use the seek button to search for frequencies. You can
save up to 3 stations as presets. Follow the steps below to set a
station:
a. Find a station you want to save.
b. Press and hold one of the three preset buttons. The station
preset number (1, 2 or 3) on the display will quickly flash to con-
firm the setting. To set the additional two stations, conduct this
step again.
Connecting Your Apple Device and MP3 Player Using the USB:
• Locate the USB port in the stereo locker
• Use a 30-pin cable for compatible devices or a cable provi-
ded with your device.
• Connect the USB end of the cable into the USB connection
on stereo.
• Connect the 30-pin end of the cable to the Apple device/
MP3 Player (purchased separately).
• After connecting the cable to both devices, set the player
into the rubber holding base.
USB
AUX
(purchased separately)
Note: The DRM (Digital Rights Management) Files cannot be
played on this deck. Personal files (MP3, WMA, iTunes or AAC) can
be played as long as they are not DRM encrypted.
Operating USB/MP3/Apple device
• Turn power "ON" to the stereo unit. Turn power "ON" to the
remote.
• The LCD screen on the remote will display the following:
"Welcome, " "USB, " "Load, " "Apple" (final display will vary de-
pending on the device connected). All functions are perfor-
med through the remote.
• While the music is playing the remote screen will display
and continually scroll through the following: Artist, Album,
Song and Track information.
• For operational functions refer to the "External Media Devi-
ce Playback" section.
Operating the USB drive:
• Plug in your USB device into the "USB" connection on the
stereo.
• Turn power "ON" to the stereo unit and the stereo remote.
• The LCD screen on the remote will display the following:
"Welcome, " "USB, " "Load, " "TOL XX" (final display will vary de-
pending on the whether the USB holds folders or files). All
functions are performed through the remote.
• While the music is playing the remote screen will display
and continually scroll through the following: Title, Song, Ar-
tist, Album, Dir, Music and Track information.
• For operational functions refer to the "External Media Devi-
ce Playback" section.
Connecting Your Auxiliary Player Using the 3.5 mm Cable:
• Plug one end of the cable to "Aux" connection on the stereo.
• Plug the other end of the cable into the phone jack con-
nection on the Apple device/MP3 Player.
• Press the Mode button on the remote to "AUX IN.
• All playback operations are conducted via the Auxiliary
Player. The stereo remote functions do not work on the ex-
ternal Auxiliary Player (except volume control).
USB USB
AUX AUX
Connecting Your Bluetooth Device:
• Turn power "ON" to the stereo unit.
• From your Bluetooth device, make sure the Bluetooth set-
ting is "ON. "
• Follow the pairing instructions for your Bluetooth device
and connect to the "BLUEWAVE" device that appears on
your screen.
• If asked for a password, enter the code "0000. "
• The remote LCD screen will display, "BT AUDIO" if the pro-
USB
AUX
cess was successful.
ACCESSORY CONNECTED
Operating Your Bluetooth Device:
• Press the seek up or down buttons to scroll through the
tracks (on the remote).
• Press the volume up or down buttons to adjust volume le-
vel between 0 to 30 (on the remote).
• Any other playback operations are conducted via the Blue-
tooth device.
41