Roland VR-1HD Reference Manual page 35

USB FROM PC
DIGITAL GAIN
LEVEL
MUTE
SOLO
REVERB SEND
AUX SEND
DELAY
EQ
SW
HI
HI FREQ
MID
MID FREQ
MID Q
LO
LO FREQ
PLAYBACK (BGM/SE)
DIGITAL GAIN
LEVEL
MUTE
SOLO
REVERB SEND
AUX SEND
EQ
SW
HI
HI FREQ
MID
MID FREQ
MID Q
LO
LO FREQ
(*8) The number of frames shown in parentheses differs depending on the SYSTEM menu's "FRAME RATE" setting.
Adjusts the audio that is input from the USB STREAM port.
-42.0–0 0–42.0dB Adjusts the input gain (sensitivity).
-INF–0 0–10.0dB Adjusts the input volume.
OFF, ON Turns the mute function on/off. If this is "ON, " the audio is temporarily silenced.
Turns the solo function on/off. Only the audio for which this is "ON" is heard in the
headphones.
OFF, ON
* The solo function applies to the headphone output. It does not affect output other than
-INF–0 0–10.0dB Adjusts the amount of audio sent to reverb.
-INF–0 0–10.0dB Adjusts the amount of audio sent to the AUX bus.
Adjusts the delay time of the audio.
0 0–500.0ms (*8)
(0 0–29.9/25.0frame)
(OFF, ON) Press the [VALUE] knob to access the EQ (equalizer) menu.
Turns the equalizer on/off.
OFF, ON
0–15.0dB
-15.0–0 Boosts or attenuates the high band.
0–20.0kHz
1.00–10 Adjusts the center frequency when changing the tone quality in the high band.
0–15.0dB
-15.0–0 Boosts or attenuates the middle band.
20.0Hz–500Hz–20.0kHz Adjusts the center frequency when changing the tone quality in the middle band.
0–16.0
0.5–1 Adjusts the width of the frequency band when boosting or attenuating the middle band.
0–15.0dB
-15.0–0 Boosts or attenuates the low band.
20.0–100–500Hz Adjusts the center frequency when changing the tone quality in the low band.
Adjust the audio of the music file (background music or sound effects) that is being played.
-12 0–42.0dB
-42.0– Adjusts the input gain (sensitivity).
0–10.0dB
-INF–0 Adjusts the input volume.
OFF, ON
Turns the mute function on/off. If this is "ON, " the audio is temporarily silenced.
Turns the solo function on/off. Only the audio for which this is "ON" is heard in the
headphones.
OFF, ON
* The solo function applies to the headphone output. It does not affect output other than
0–10.0dB
-INF–0 Adjusts the amount of audio sent to reverb.
0–10.0dB
-INF–0 Adjusts the amount of audio sent to the AUX bus.
(OFF, ON) Press the [VALUE] knob to access the EQ (equalizer) menu.
Turns the equalizer on/off.
OFF, ON
-15.0–0 0–15.0dB Boosts or attenuates the high band.
1.00–10 0–20.0kHz Adjusts the center frequency when changing the tone quality in the high band.
-15.0–0 0–15.0dB Boosts or attenuates the middle band.
20.0Hz–500Hz–20.0kHz Adjusts the center frequency when changing the tone quality in the middle band.
0.5–1 0–16.0 Adjusts the width of the frequency band when boosting or attenuating the middle band.
-15.0–0 0–15.0dB Boosts or attenuates the low band.
20.0–100–500Hz Adjusts the center frequency when changing the tone quality in the low band.
the headphones.
Effect Delays the output of the audio by the specified time.
Effect Adjusts the tone quality for each frequency band.
the headphones.
Effect Adjusts the tone quality for each frequency band.
Menu List
35