E-FLITE P-51D Mustang 1.2m Instruction Manual
Bnf basic, as3x safe, pnp plug-n-play
Hide thumbs
Also See for P-51D Mustang 1.2m:
- Instruction manual (17 pages) ,
- Instruction manual (20 pages)
Related Manuals for E-FLITE P-51D Mustang 1.2m
Summary of Contents for E-FLITE P-51D Mustang 1.2m
- Page 1 P-51D Mustang 1.2m Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni NOTE: Actual model trim scheme may vary EFL8950 EFL8975...
- Page 2 • Always charge batteries away from fl ammable materials. • Never charge batteries in extremely hot or cold places (recommended • Always inspect the battery before charging and never charge between 40–120° F or 5–49° C) or place in direct sunlight. damaged batteries. P-51D Mustang 1.2m...
-
Page 3: Table Of Contents
Box Contents Quick Start Information Transmitter Set up your transmitter using the Setup transmitter setup chart Hi Rate Low Rate 12mm 15mm 11mm Dual Rates 15mm 10mm Landing Takeoff Flaps =50mm =11mm Center of 85mm +/- 3 back from leading edge at the root. -
Page 4: Prefl Ight
WING: 1 AIL 1 FLAP 4. Go to the FUNCTION LIST 5. Set SERVO SETUP: Reverse GEAR 6. Set FLAP SYSTEM: DX10t SELECT SWITCH D: DX18 POS 0: 100% FLAP POS 1: 0% FLAP POS 2: -90% FLAP SPEED 2.0 P-51D Mustang 1.2m... -
Page 5: Model Assembly
Model Assembly Horizontal Tail Installation 1. Slide the horizontal tail tube (A) into the hole in the rear of the fuselage. 2. Install the 2 piece (left and right) horizontal tail as shown. Ensure the control horn faces down. 3. Secure the two horizontal tail pieces in place using the 2 included screws (B). 4. -
Page 6: Model Assembly Continued
If adjustment is required, turn the clevis on the linkage to change the length of the linkage between the servo arm and the control horn. After binding a transmitter to the aircraft receiver, set the trims and sub-trims to 0, then adjust the clevises to center the control surfaces. P-51D Mustang 1.2m... -
Page 7: Model Assembly Continued
Model Assembly Continued Propeller Installation IMPORTANT: It is recommended to install the propeller after all system setups are completed to reduce the chance of accidental propeller strike. 1. Install the spinner back plate (E), propeller (D) and collet (C) onto the motor shaft (F). -
Page 8: Optional Antenna Mast Installation
If the ESC sounds a continuous double beep after the fl ight battery is connected, recharge or replace the battery. 9. Reinstall the canopy hatch. CAUTION: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement. P-51D Mustang 1.2m... -
Page 9: Transmitter And Receiver Binding-Switching On/Off Safe
® Transmitter and Receiver Binding / Switching ON and OFF SAFE Select Switching ON SAFE Select Binding Sequence This product requires an approved Spektrum™ DSM2®/DSMX® compatible transmitter. Visit www.bindnfl y.com for a complete list of approved transmitters. The aircraft has an optional SAFE Select feature, which can be switched ON or OFF easily by binding in a specifi... -
Page 10: Center Of Gravity (Cg)
fl y the aircraft. Refer to the receiver manual for more information. Once the AS3X system is active, control surfaces may move rapidly. This is normal. AS3X remains active until the battery is disconnected. P-51D Mustang 1.2m... -
Page 11: In Flight Trimming
In Flight Trimming During your fi rst fl ight, trim the aircraft for level fl ight at 3/4 throttle with fl aps and gear up. Make small trim adjustments with your transmitter’s trim switches to straighten the aircraft’s fl ight path. 3 Seconds After adjusting trim do not touch the control sticks for 3 seconds. -
Page 12: Post Flight
Incorrect response Incorrect direction settings to the AS3X Control in the receiver, which can DO NOT fl y. Correct the direction settings (refer to the receiver manual), then fl y Direction Test cause a crash P-51D Mustang 1.2m... -
Page 13: Troubleshooting Guide
Troubleshooting Guide Problem Possible Cause Solution Throttle not at idle and/or throttle trim too high Reset controls with throttle stick and throttle trim at lowest setting Aircraft will not Throttle servo travel is lower than 100% Make sure throttle servo travel is 100% or greater respond to throttle but responds to Throttle channel is reversed... -
Page 14: Ama National Model Aircraft Safety Code
(b) An inexperienced pilot is assisted by an experienced pilot. 4. When and where required by rule, helmets must be properly worn and fastened. They must be OSHA, DOT, ANSI, SNELL or NOCSAE approved or comply with comparable standards. P-51D Mustang 1.2m... -
Page 15: Limited Warranty
Limited Warranty What this Warranty Covers – Horizon Hobby, LLC, (Horizon) warrants to the original our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the purchaser that the product purchased (the “Product”) will be free from defects in toll free telephone number referenced in the Warranty and Service Contact Information materials and workmanship at the date of purchase. -
Page 16: Contact Information
For more information about where you can drop off your waste equipment for recycling, please contact your local city offi ce, your household waste disposal service or where you purchased the product. P-51D Mustang 1.2m... -
Page 17: Replacement Parts
Description Beschreibung Description Descrizione Numéro | Codice EFL8250 P-51D Mustang 1.2m BNF Basic P-51D Mustang 1,2m BNF Basic P-51D Mustang 1.2m BNF Basic P-51D Mustang 1.2m BNF Basic P-51D 1.2m - Cône diamètre 75mm EFL8201 Spinner 4 blade 75mm: P-51D 1.2m 4-Blatt Spinner 75mm: P-51D 1,2m Ogiva quadripala 75mm: P-51D 1.2m... - Page 18 P-51D Mustang 1.2m © 2017 Horizon Hobby, LLC. E-fl ite, AS3X, DSM, DSM2, DSMX, the DSMX logo, Bind-N-Fly, the BNF logo, SAFE, the SAFE logo, Z-Foam, ModelMatch, Dynamite, EC3, Celectra, Prophet and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.