Table of Contents
Advertisement
601
G0701
614
600V2
MODEL G0701
19" ULTIMATE BANDSAW
Specifications
WARNING!
Motor: 5 HP, 230V, Single-Phase, 60 Hz
To reduce risk of serious injury when using this machine:
Full-Load Amp Draw: 27A
1. Read and understand owner's manual before operating.
Table Size: 28" x 24"
2. Never touch moving blade. Keep hands out of blade path.
Blade Speed: 4975 FPM
3. Always wear approved eye protection and respirator.
Blade Length: 166" – 168"
4. Properly ground machine—connect to permanently grounded
Blade Width Range: 3/8" – 1-3/8"
metal wiring system or an equipment-grounding conductor.
Max. Cutting Width Left of Blade: 18-3/8"
5. Only remove jammed cutoff pieces when blade is stopped.
Max. Cutting Height: 19-1/2"
6. Use push stick or holding jig to cut small or narrow pieces.
Table Tilt: 5˚L ⁄ 45˚R
7. Disconnect power before changing blades or adjusting saw.
Weight: 717 lbs.
8. Maintain adjustment of blade tension, tracking, and guides.
9. Keep upper guide adjusted to just clear the workpiece.
10. Hold workpiece firmly against table to maintain control.
11. Only run saw with wheel covers closed and all guards in place.
12. Never reach under table while blade is in motion.
Date
13. Remove/secure loose clothing and long hair.
14. DO NOT expose to rain or use in wet locations.
SN
15. Prevent unauthorized use by children or untrained users;
Mfd. for Grizzly in Taiwan
restrict access or disable machine when unattended.
G0701 Labels B
• 1:1 Sizing (Labels are
610
actual size)
(4/10/14)
• Labels must be made of
oil-resistant material
Note: All labels on this page are NEW or have CHANGED since original sending.
GUIDE POST POSITION
UP
DOWN
NOTICE
G0701 Labels C
Do not attempt to move guide post while it is in
locked position. Failure to loosen guide post lock
knob before adjusting guide post position may
G0701 Labels C
• 1:1 Sizing (Labels are
result in machine damage.
(4/10/14)
actual size)
(4/10/14)
• Labels must be made of
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY!
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.
If
oil-resistant material
artwork changes are required, contact us immediately at manuals@grizzly.com.
Note: All labels on this page are NEW or have CHANGED since original sending.
608
Note: All labels on this page are NEW or have CHANGED since original sending.
WARNING!
NOTICE
Before adjusting table angle,
To reduce risk of death
INJURY HAZARD!
WARNING!
or serious injury, read
release table lock lever.
manual BEFORE using
Do not open door
Before adjusting table angle,
To reduce risk of death
machine.
INJURY HAZARD!
while machine is
or serious injury, read
To get a new manual,
connected to power
release table lock lever.
manual BEFORE using
Do not open door
call (800) 523-4777 or
machine.
or blade is in motion.
go to www.grizzly.com.
while machine is
To get a new manual,
connected to power
call (800) 523-4777 or
or blade is in motion.
go to www.grizzly.com.
NOTICE
Be sure lever is in locked
position before operating saw.
Be sure lever is in locked
position before operating saw.
WARNING!
EYE/LUNG INJURY
WARNING!
HAZARD!
EYE/LUNG INJURY
Always wear safety
glasses and a
HAZARD!
respirator when
Always wear safety
using this machine.
glasses and a
respirator when
611
using this machine.
COLOR CODES
COLOR CODES
DANGER
PANTONE 485 C or RAL 3001
WARNING
PANTONE 151 C or RAL 2005
DANGER
PANTONE 485 C or RAL 3001
CAUTION
PANTONE 109 C
WARNING
PANTONE 151 C or RAL 2005
NOTICE
PANTONE 3005 C or RAL 5005
CAUTION
PANTONE 109 C
NOTICE
PANTONE 3005 C or RAL 5005
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY!
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.
FOR GRIZZLY MACHINES ONLY!
607
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
artwork changes are required, contact us immediately at manuals@grizzly.com.
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.
artwork changes are required, contact us immediately at manuals@grizzly.com.
606
613
REF
PART #
DESCRIPTION
600V2 P0701600V2
MACHINE ID LABEL V2.02.18
601
P0701601
MODEL NUMBER LABEL
602
P0701602
DOOR WARNING LABEL
605
P0701605
DISCONNECT POWER LABEL
606
P0701606
TOUCH-UP PAINT, GRIZZLY PUTTY
607
P0701607
TOUCH-UP PAINT, GRIZZLY GREEN
608
P0701608
READ MANUAL LABEL
609
P0701609
ELECTRICITY LABEL
610
P0701610
GUIDE POST ELEVATION LABEL
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
BUY PARTS ONLINE AT GRIZZLY.COM!
-82-
Scan QR code to visit our Parts Store.
Labels & Cosmetics
G0701 Labels C
• 1:1 Sizing (Labels are
actual size)
(4/10/14)
• Labels must be made of
oil-resistant material
Note: All labels on this page are NEW or have CHANGED since original sending.
NOTICE
WARNING!
To reduce risk of death
Before adjusting table angle,
INJURY HAZARD!
or serious injury, read
manual BEFORE using
Do not open door
release table lock lever.
machine.
while machine is
To get a new manual,
connected to power
call (800) 523-4777 or
or blade is in motion.
go to www.grizzly.com.
NOTICE
Be sure lever is in locked
position before operating saw.
• 1:1 Sizing (Labels are
WARNING!
actual size)
EYE/LUNG INJURY
HAZARD!
• Labels must be made of
Always wear safety
glasses and a
respirator when
oil-resistant material
using this machine.
609
COLOR CODES
DANGER
PANTONE 485 C or RAL 3001
WARNING
PANTONE 151 C or RAL 2005
CAUTION
PANTONE 109 C
NOTICE
PANTONE 3005 C or RAL 5005
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY!
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.
If
artwork changes are required, contact us immediately at manuals@grizzly.com.
NOTICE
NOTICE
G0636X, G0636XB
Generic Labels
(3/17/14)
If
If
Note: All labels on this page are NEW or have CHANGED since original sending.
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
COLOR CODES
DANGER
PANTONE 485 C or RAL 3001
WARNING
PANTONE 151 C or RAL 2005
Before adjusting table angle,
INJURY HAZARD!
or serious injury, read
release table lock lever.
manual BEFORE using
Do not open door
618
machine.
while machine is
To get a new manual,
connected to power
call (800) 523-4777 or
or blade is in motion.
go to www.grizzly.com.
NOTICE
Be sure lever is in locked
position before operating saw.
G0701 Labels C
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
(4/10/14)
WARNING!
oil-resistant material
EYE/LUNG INJURY
HAZARD!
Always wear safety
602
Note: All labels on this page are NEW or have CHANGED since original sending.
glasses and a
respirator when
using this machine.
COLOR CODES
DANGER
PANTONE 485 C or RAL 3001
NOTICE
WARNING
PANTONE 151 C or RAL 2005
WARNING!
617
Before adjusting table angle,
To reduce risk of death
CAUTION
PANTONE 109 C
INJURY HAZARD!
or serious injury, read
release table lock lever.
manual BEFORE using
Do not open door
machine.
NOTICE
PANTONE 3005 C or RAL 5005
while machine is
To get a new manual,
connected to power
call (800) 523-4777 or
or blade is in motion.
go to www.grizzly.com.
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
NOTICE
FOR GRIZZLY MACHINES ONLY!
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.
Be sure lever is in locked
artwork changes are required, contact us immediately at manuals@grizzly.com.
position before operating saw.
605
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
COLOR CODES
DANGER
PANTONE 485 C or RAL 3001
WARNING
PANTONE 151 C or RAL 2005
CAUTION
PANTONE 109 C
NOTICE
PANTONE 3005 C or RAL 5005
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY!
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.
If
artwork changes are required, contact us immediately at manuals@grizzly.com.
G0701 Labels C
• 1:1 Sizing (Labels are
actual size)
(4/10/14)
• Labels must be made of
616
oil-resistant material
Note: All labels on this page are NEW or have CHANGED since original sending.
NOTICE
WARNING!
To reduce risk of death
Before adjusting table angle,
INJURY HAZARD!
or serious injury, read
• 1:1 Sizing (Labels are
release table lock lever.
manual BEFORE using
Do not open door
machine.
while machine is
actual size)
To get a new manual,
connected to power
call (800) 523-4777 or
or blade is in motion.
• Labels must be made of
go to www.grizzly.com.
NOTICE
oil-resistant material
602
Be sure lever is in locked
position before operating saw.
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
615
glasses and a
respirator when
using this machine.
NOTICE
COLOR CODES
DANGER
PANTONE 485 C or RAL 3001
Before adjusting table angle,
INJURY HAZARD!
WARNING
PANTONE 151 C or RAL 2005
release table lock lever.
Do not open door
CAUTION
PANTONE 109 C
while machine is
connected to power
NOTICE
PANTONE 3005 C or RAL 5005
or blade is in motion.
NOTICE
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY!
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.
If
Be sure lever is in locked
artwork changes are required, contact us immediately at manuals@grizzly.com.
position before operating saw.
612
USE MAGNETIC BRAKE NOTICE ONLY ON G0636XB
NOTICE
Magnetic brake remains engaged
when machine is off. To disengage
brake and avoid unnecessary
power consumption when finished
using saw, turn switch disabling
REF PART #
key to "0".
611
P0701611
612
P0701612
613
P0701613
614
P0701614
615
P0701615
616
P0701616
617
P0701617
618
P0701618
If
G0701 Labels C
(4/10/14)
Note: All labels on this page are NEW or have CHANGED since original sending.
WARNING!
To reduce risk of death
INJURY HAZARD!
or serious injury, read
manual BEFORE using
Do not open door
machine.
while machine is
To get a new manual,
connected to power
call (800) 523-4777 or
or blade is in motion.
go to www.grizzly.com.
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
COLOR CODES
DANGER
PANTONE 485 C or RAL 3001
WARNING
PANTONE 151 C or RAL 2005
CAUTION
PANTONE 109 C
NOTICE
PANTONE 3005 C or RAL 5005
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY!
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.
artwork changes are required, contact us immediately at manuals@grizzly.com.
DESCRIPTION
GLASSES/RESPIRATOR LABEL
GRIZZLY.COM LABEL
EXTREME SERIES PLATE
GRIZZLY NAMEPLATE
TABLE LOCK NOTICE
ANGLE LOCK LABEL
GUIDE POST LOCK NOTICE
WHEEL LOCK LEVER NOTICE
Model G0701 (Mfd. Since 9/17)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material
NOTICE
Before adjusting table angle,
release table lock lever.
NOTICE
Be sure lever is in locked
position before operating saw.
609
DO NOT REPRODUCE OR CHANGE THIS ARTWORK
If
Advertisement
Table of Contents
