York LINC GATEWAY 514067-UAD-A-0509 Application Manual page 4

514067-UAD-A-0509
TABLE 2: POINTS LIST IN DESCRIPTION ORDER
BACnet
Read/ Object
Write Type
R (2) AV
R (2) AV
R (5) BV
R/W (2) AV
R (5) BV
R (5) BV
R (5) BV
R (5) BV
R (5) BV
R (2) AV
R (5) BV
R/W (2) AV
R/W (2) AV
R (5) BV
R (5) BV
R (5) BV
R/W (2) AV
R (5) BV
R (5) BV
R (2) AV
R (2) AV
R (5) BV
R/W (2) AV
R (2) AV
R (5) BV
R (5) BV
R (2) AV
R/W (2) AV
R/W (2) AV
R (2) AV
4
BACnet
Object
Inst Descriptor
14 ACC_OVER_TME
15 ACTIVE_ALARM
16 AIR_PROOF_SW
79 OAQ_STPT
85 ALARM_1_ON
86 ALARM_2_ON
87 ALARM_3_ON
88 ALARM_4_ON
89 ALARM_5_ON
33 BLDG_STATIC
29 BP_SENS_INST
57 BLDG_SP_STPT
25 COM_V_LOW_SP
34 CVM_COOLING
35 CVM_HEATING
33 COM_VENT_STA
24 COM_V_HI_SP
23 COOLING_ENA
21 FAN_ON_W_SEN
56 CV_VAV_SELEC
8 IAQ_VALUE
39 DEMAND_VENT
18 DEMVENT_STPT
67 REVISION
90 DF_SW_INST
15 DIRT_FILT_SW
35 DUCT_STATIC
58 DUCT_SP_STPT
59 DUCT_SD_STPT
31 ECO_DAMP_OUT
Default Min Max Point Description
– – – Accumulated Unoccupied Override Time
(in hours)
– – – Active Alarm
– – – Air Proving Switch Status (1=closed,
0=open/no air flow)
1000 0 5000 Air Quality Setpoint Outside
– – – Alarm Buffer #1 (0=Alarm has cleared,
1=Alarm is still active)
– – – Alarm Buffer #2 (0=Alarm has cleared,
1=Alarm is still active)
– – – Alarm Buffer #3 (0=Alarm has cleared,
1=Alarm is still active)
– – – Alarm Buffer #4 (0=Alarm has cleared,
1=Alarm is still active)
– – – Alarm Buffer #5 (0=Alarm has cleared,
1=Alarm is still active)
– – – Building Static Pressure
– – – Building Static Pressure Sensor Installed
0.1 -0.25 0.25 Building Static Pressure Setpoint
70 60 85 Comfort Ventilation LowerSetpoint
(degrees F)
– – – Comfort Ventilation Mode for Cooling
Enabled
– – – Comfort Ventilation Mode for Heating
Enabled
– – – Comfort Ventilation Mode Status (1=control
is in Comfort Vent mode, 0= it is not)
80 60 85 Comfort Ventilation Upper Setpoint
(degrees F)
– – – Cooling Mode Enabled
– – – CV - Indoor Fan Operates with Space
Sensor Present Option Enabled
– – – CV/VAV Selected (0= Valid CV, 1=Valid
VAV, 2= Invalid Value)
– – – Demand Ventilation (IAQ) Value (PPM)
– – – Demand Ventilation (using Inside Sensor)
Enabled
1000 0 5000 Demand Ventilation Setpoint
– – xx Device Revision
– – – Dirty Filter Switch Installed
– – – Dirty Filter Switch Status (0=open,1=closed/
fault)
– – – Duct Static Pressure
1.5 0 5 Duct Static Pressure Setpoint
4.5 0 5 Duct Static Pressure Shutdown Setpoint
– – – Economizer Damper Output Status
(0-100%)
Johnson Controls Unitary Products