Boom Specifications - Alamo MACHETE Product Service Manual

SPECIFICATIONS - MACHETE
1. Cutting Circuit Specifications
Hyd. Pump Speed
Hyd. Motor Speed.................................................................. 1220 RPM
Hyd. Motor Rated HP............................................................. 199 HP
Hyd. Motor Rotation
Relief Valve Setting At Motor................................................. 4000 PSI
Relief Valve Setting At Pump................................................ 4500 PSI
Hyd. Pump Flow
Hyd. Oil Operating Temperature.......................................... 95 Deg, (F) Above Ambient
Hyd. Oil Filtration,
Hyd. Tank Capacity............................................................... 17 Gal.
Hyd. Motor Circuit Oil Type *................................................ ISO AW 100 Hyd Oil
Hyd. Motor Start Stop Time (Approximate)........................... 6 Seconds
Cutting Diameter, (Rotary Head).......................................... 58 Inch
Spindle................................................................................... 4.5 " by 9" Heat Treated Alloy
Blade Bar Type...................................................................... Stacked 3 Leaf
Blade Bar Size....................................................................... 1-1/4" Thick X 5" Wide (Ea. Leaf)
Blade Bar Material.... Bottom Leaf....................................... T1 Steel
Blade Swing........................................................................... 360 Deg Swing
Blade Material........................................................................ High Carbon Alloy Steel
Cutter Weight. (Approximate w/ Rotary Head)..................... 950 lbs.
Cutter Deck Opening & Closing........................................... Hyd. Operated Door
* Older models recommended Universal Tractor Hydraulic Oil, This was changed to ISO
AW 100 Hyd. Oil, If changing Oil in Older units switch to New Oil, DO NOT Mix types of Oil.

2. BOOM SPECIFICATIONS

Boom Reach 21 Foot Boom...............................
24 Foot Boom.......................................................
Frame (Old Low Frame).......................................
(New High Frame).....................................
Pins.......................................................................
Bushings...............................................................
Weight (vary w/ size of Boom not include Head)..
Weight, Head Only (Add to Boom when used).....
Boom Rest............................................................
Boom Mounting.....................................................
3. FILTRATION
Control Valve F
powered by the Tractor Hydraulic System and are protected by the Tractors Filtration system.
Maintenance and specification of this should be per Tractor Manufacturer instructions. Later
Models Had an Inline Filter assembly (P/N 02976066) added to Filter Tractor System between
Valve and Tractor. Change Filter every 200 to 250 hrs. Operation recommended maximum.
Mower Head Functions: Mower
to the front of the Tractor Engine. This will have an inline Filter installed into hydraulic circuit,
This filter should be changed on a regular maintenance schedule. Filter are rated by Micron size
(10 Micron), Filter should be replaced with the same Micron and High Pressure rated Filter.
Machete (Service Manual) 04/04
© 2004 Alamo Group Inc.
...................................... 1950 RPM
(Front Aux Pump)
(as viewed f/ Top of the Deck)
(Front Pump @ 1950 RPM)
(Discharge f/ Charge Pump).
Middle & Top Leaf............................. HRFB Steel
unctions: Control
Head Functions are operated by Pump, which is mounted
................... CW (Clockwise)
.......................... 25.3 GPM
........................ 10 Micron
Up 20'-3"
Up 23'
4" X 6" Rect, Tube
4 X 4 Sq. Sq. Tube (formed corners)
Chromed
Self Lubricating (No grease needed)
21 ft = 2250 lbs.
60" Rotary = 950 lbs., 48" Flail = 770 lbs.,
FML100H = 990 lbs.
Tractor Axle Mounted
ROPS or CAB Tractor Optional
functions include All Hydraulic Cylinders, These are
10
Out 21'-4" Down 12'-11"
Out 24'-2" Down 14'-5"
24 ft = 2300 lbs.