Siemens Siprotec 7VK61 Manual page 287

Addr. Parameter
610 FltDisp.LED/LCD
625A T MIN LED HOLD
640 Start image DD
1103 FullScaleVolt.
1104 FullScaleCurr.
1107 P,Q sign
1130A PoleOpenCurrent
1131A PoleOpenVoltage
1133A T DELAY SOTF
1135 Reset Trip CMD
1136 OpenPoleDetect.
1150A SI Time Man.Cl
1151 MAN. CLOSE
1152 Man.Clos. Imp.
2601 Operating Mode
2610 Iph>>
2611 T Iph>>
2612 3I0>> PICKUP
2613 T 3I0>>
2614 I>> Telep/BI
2615 I>> SOTF
2620 Iph>
2621 T Iph>
2622 3I0>
2623 T 3I0>
2624 I> Telep/BI
2625 I> SOTF
2630 Iph> STUB
2631 T Iph STUB
2632 3I0> STUB
2633 T 3I0 STUB
SIPROTEC, 7VK61, Manual
C53000-G1176-C159-3, Release date 05.2009
Function C
Device Target on PU
Target on TRIP
0 .. 60 min; ∞
Device
Device image 1
image 2
image 3
image 4
image 5
image 6
P.System Data 2 1.0 .. 1200.0 kV
P.System Data 2 10 .. 5000 A
P.System Data 2 not reversed
reversed
P.System Data 2 1A 0.05 .. 1.00 A
5A 0.25 .. 5.00 A
P.System Data 2 2 .. 70 V
P.System Data 2 0.05 .. 30.00 sec
P.System Data 2 CurrentOpenPole
Current AND CB
Pickup Reset
P.System Data 2 OFF
Current AND CB
w/ measurement
P.System Data 2 0.01 .. 30.00 sec
P.System Data 2 with Sync-check
w/o Sync-check
NO
P.System Data 2 (Setting options depend
on configuration)
Back-Up O/C ON
OFF
0.10 .. 25.00 A; ∞
Back-Up O/C 1A
0.50 .. 125.00 A; ∞
5A
0.00 .. 30.00 sec; ∞
Back-Up O/C
0.05 .. 25.00 A; ∞
Back-Up O/C 1A
0.25 .. 125.00 A; ∞
5A
0.00 .. 30.00 sec; ∞
Back-Up O/C
Back-Up O/C NO
YES
Back-Up O/C NO
YES
0.10 .. 25.00 A; ∞
Back-Up O/C 1A
0.50 .. 125.00 A; ∞
5A
0.00 .. 30.00 sec; ∞
Back-Up O/C
0.05 .. 25.00 A; ∞
Back-Up O/C 1A
0.25 .. 125.00 A; ∞
5A
0.00 .. 30.00 sec; ∞
Back-Up O/C
Back-Up O/C NO
YES
Back-Up O/C NO
YES
0.10 .. 25.00 A; ∞
Back-Up O/C 1A
0.50 .. 125.00 A; ∞
5A
0.00 .. 30.00 sec; ∞
Back-Up O/C
0.05 .. 25.00 A; ∞
Back-Up O/C 1A
0.25 .. 125.00 A; ∞
5A
0.00 .. 30.00 sec; ∞
Back-Up O/C
Setting Options Default Setting
Target on PU
0 min
image 1
400.0 kV
1000 A
not reversed
0.10 A
0.50 A
30 V
0.25 sec
CurrentOpenPole
w/ measurement
0.30 sec
NO
None
ON
2.00 A
10.00 A
0.30 sec
0.50 A
2.50 A
2.00 sec
YES
NO
1.50 A
7.50 A
0.50 sec
0.20 A
1.00 A
2.00 sec
NO
NO
1.50 A
7.50 A
0.30 sec
0.20 A
1.00 A
2.00 sec
Appendix
A.7 Settings
Comments
Fault Display on LED / LCD
Minimum hold time of lachted
LEDs
Start image Default Display
Measurement: Full Scale Voltage
(100%)
Measurement: Full Scale Current
(100%)
P,Q operational measured values
sign
Pole Open Current Threshold
Pole Open Voltage Threshold
minimal time for line open before
SOTF
RESET of Trip Command
open pole detector
Seal-in Time after MANUAL clo-
sures
Manual CLOSE COMMAND
generation
MANUAL Closure Impulse after
CONTROL
Operating mode
Iph>> Pickup
T Iph>> Time delay
3I0>> Pickup
T 3I0>> Time delay
Instantaneous trip via Tele-
prot./BI
Instantaneous trip after Switch-
OnToFault
Iph> Pickup
T Iph> Time delay
3I0> Pickup
T 3I0> Time delay
Instantaneous trip via Tele-
prot./BI
Instantaneous trip after Switch-
OnToFault
Iph> STUB Pickup
T Iph STUB Time delay
3I0> STUB Pickup
T 3I0 STUB Time delay
287