Analog/Digital Outputs - Trane TR1 6002 Installation And Operation Manual

Analog/Digital Outputs

The two analog/digital outputs available through terminals 42 and 45
can be programmed to show a status or an analog value such as
frequency. The status signal is a 24 VDC output.
Analog/Digital Outputs
Analog/Digital Outputs
Value:
No function (NO FUNCTION)
Drive ready (READY)
Standby (ENABLED & NO WARNING)
Running (RUNNING)
Running at ref. value (RUNNING AT REFERENCE)
Running, no warning (RUNNING NO WARNING)
Local reference active (DRIVE IN LOCAL REF.)
Remote controlled references active (DRIVE IN REMOTE REF.)
Alarm (ALARM)
Alarm or warning (ALARM OR WARNING)
No alarm (NO ALARM)
Current limit (CURRENT LIMIT)
Safety interlock (SAFETY INTERLOCK)
Start command active (START SIGNAL APPLIED)
Reversing (RUNNING IN REVERSE)
Thermal warning (THERMAL WARNING)
Hand mode active (DRIVE IN HAND MODE)
Auto mode active (DRIVE IN AUTO MODE)
Sleep mode (SLEEP MODE)
Output frequency lower than parameter 223 (F OUT < F LOW)
Output frequency higher than parameter 223 (F OUT > F HIGH)
Out of frequency range (FREQ. RANGE WARN.)
Output current lower than low current, parameter 221 (I OUT < I LOW)
Output current higher than high current, parameter 222 (I OUT > I HIGH)
Out of current range (CURRENT RANGE WARN)
Out of feedback range (FEEDBACK RANGE WARN.)
Out of reference range (REFERENCE RANGE WARN)
Relay 123 (RELAY 123)
Input phase loss (MAINS PHASE LOSS)
Output frequency, (OUT. FREQ. 0-20 mA)
Output frequency, (OUT. FREQ. 4-20 mA)
Output frequency (pulse sequence), (OUT. FREQ. PULSE)
External reference, (EXT. REF. 0-20 mA)
External reference, (EXTERNAL REF. 4-20 mA)
External reference (pulse sequence), (EXTERNAL REF. PULSE)
Feedback, (FEEDBACK 0-20 mA)
Feedback, (FEEDBACK 4-20 mA)
Feedback (pulse sequence), (FEEDBACK PULSE)
Output current, 0-20 mA (MOTOR CUR. 0-20mA)
Output current, 4-20 mA (MOTOR CUR. 4-20mA)
Output current (pulse sequence), (MOTOR CUR PULSE)
Output power, 0-20 mA (MOTOR POWER 0-20mA)
Output power, 4-20 mA (MOTOR POWER 4-20mA)
Output power (pulse sequence), 0- 32000 pulses (MOTOR POWER PULSE)
Controlled by serial bus: 0-20 mA (BUS CONTROL 0-20MA)
Controlled by serial bus: 4-20 mA (BUS CONTROL 4-20MA)
Controlled by serial bus: pulses (BUS CONTROL PULSE)
✭ I
ndicates factory default setting. Numbers in brackets [ ] represent selection as displayed on the serial bus.
58
For the analog output, there is a choice of three types of output signal:
0 to 20 mA, 4 to 20 mA or 0 to 32000 pulses. The pulse rate is set by
parameter 322, Terminal 45, Output, Pulse Scaling.
See the Electrical Installation, Control Terminals section of this manual
for the ratings of these outputs.
Terminal Number:
Parameter:
★ [39]
terminal no.
42 45
319 321
[0] [0]
[1] [1]
[2] [2]
[3] [3]
[4] [4]
[5] [5]
[6] [6]
[7] [7]
[8] [8]
[9] [9]
[10] [10]
[11] [11]
[12] [12]
[13] [13]
[14] [14]
[15] [15]
[16] [16]
[17] [17]
[18] [18]
[19] [19]
[20] [20]
[21] [21]
[22] [22]
[23] [23]
[24] [24]
[25] [25]
[26] [26]
[27] [27]
[28] [28]
[29] [29]
★ [30]
[30]
[31] [31]
[32] [32]
[33] [33]
[34] [34]
[35] [35]
[36] [36]
[37] [37]
[38] [38]
[39]
[40] [40]
[41] [41]
[42] [42]
[43] [43]
[44] [44]
[45] [45]
[46] [46]