Alcatel-Lucent MDR-8000 User Manual page 45

Audio provisioning is required only if 4-wire audio equipment (external equipment not part of
the radio) is supplied and the external audio equipment is connected to audio port 1 J316 or
Alcatel User Interface – [System, DS3, and DS1 Provisioning -- MDR-8000 DS3]
audio port 2 J317 on the radio backplane. These provisionable 4-wire audio functions should
File View Setup Options
not be confused with the 2-wire audio handset. The handset is fully operational after it is
connected to the TEL jack on the radio controller module, provided the radio is provisioned
F3 F4
Audio 1.
Prov. Save Alarm Status
The most common audio provisioning is: 1:, 2:, or 3: AUDIO 1 0/0 Norm.
ELMC Address: J7914
ELMC Description: DURANGO
Radio Configuration
AUDIO 1: Channel
Level
AUDIO 2: Channel
Level
Channel 1
RS-232
Channel
TMN
MCS RSS
RDS/RAS/RCD
Thursday, March 7, 2000
Figure 4-20 Audio 1 Provisioning (Sheet 1 of 2)
Note
The 2-wire handset is transported over Audio 1 only.
Note
F5 F6
Analog Monitor Performance
LOCAL DS3 PROVISIONING
Communicating***
1:, 2: OR 3: – THE 64 kb/s SERVICE CHANNEL TO BE INSERTED INTO RADIO
OVERHEAD IS 1. IF SERVICE CHANNEL 1 IS ALREADY IN USE, SELECT SERVICE
CHANNEL 2 (2:) OR SERVICE CHANNEL 3 (3:) FOR THE AUDIO CHANNEL. WHATEVER
IS SELECTED FOR SERVICE CHANNEL 1, 2, OR 3, IT MUST BE THE SAME END-TO-END. Service Channel
Off E-Lead -GND
0/0 M-Lead Norm
Off E-Lead -GND
0/0 M-Lead Norm
NORM – MODE OF OPERATION SELECTED IS NORMAL. IN THIS MODE
THE RADIO REQUIRES AN OFF HOOK SIGNAL FROM THE EXTERNAL
AUDIO EQUIPMENT. THIS MEANS THAT THE AUDIO EQUIPMENT USED
Channel 2
TO CONNECT TO THE RADIO MUST HAVE E AND M-LEAD SIGNALING
CAPABILITY (MOST AUDIO EQUIPMENT DOES HAVE THIS CAPABILITY).
3 MCS Transport
IF THE EXTERNAL AUDIO EQUIPMENT DOES NOT HAVE E AND
M-LEAD SIGNALING CAPABILITY, SELECT O/H AND A CONSTANT
OFF-HOOK SIGNAL WILL BE PROVIDED AUTOMATICALLY BY THE
Address
RADIO CONTROLLER SOFTWARE.
J310 Modem
0/0 – RADIO REQUIRES 0 dBm AUDIO INPUT SIGNAL AT CONNECTOR J316.
THE RECEIVED AUDIO SIGNALS ARE NOT AMPLIFIED. THE RADIO
OUTPUTS 0 dBm ON AUDIO 1 CONNECTOR J316. THIS SELECTION IS
NORMALLY SUFFICIENT
1:27:15 PM USI Version R1.03
EQUIPMENT ARE LOCATED IN THE SAME SHELTER, ROOM AND EVEN
BUILDING. LONGER DISTANCES (SUCH AS BETWEEN BUILDINGS) MAY
REQUIRE AMPLIFICATION ON THE OUTPUT SIGNAL. IN THIS CASE,
SELECT -16/+7 WHERE THE RADIO INPUT REQUIRED IS -16 dBm AND THE
RADIO AMPLIFIES RECEIVED AUDIO SIGNALS TO PROVIDE A +7 dBm
OUTPUT AT AUDIO 1 CONNECTOR J316.
F7 F8
Station Alarm User Control
DS3 Facilities
SELECT E-Lead-24Vdc OR E-Lead GND TO
BE APPLIED TO SERVICE CHANNEL E-LEAD.
All Call Detect
2-Wire Auto Squelch
Repeater D/1
RF/Rptr PPP Transport
A12A J308/J309 Input Clocks
J308/J309 Termination
IF THE RADIO AND
Controller Version R1.03 MDR-8000 3-DS3
F9
Provisioning
WaySide DS1 Facilities
DTMF
Address 00
RF/Rptr
EXTERNAL AUDIO
MDR-1035A
09/06/04
4-35