Brakes - Chevrolet 1973 Overhaul Manual

SPECIFICATIONS 8
Stabilizer Shaft
Bracket to Frame ............................................ 120 in. lb.
Bracket to Torque Arm .................................. 120 in. lb.
Link Bushing B o lts ......................................................25
Rebound Bumper to Frame ..........................................20
Crossmember to Carrier .................................................60
Carrier Front Support
to Crossmember ........................................................ 65
Front Bolt .....................................................................50*
Rear Bolt ....................................................................... 50*
Drive Spindle N u t...........................................................100*
*Plus additional torque necessary to line up cotter pin hole.
#See Wheel Alignment Chart in Front Suspension Specification Section.
R ID IN G HEIGHTS
See "Riding Heights" in Front Suspension Specification Section.
Master Cylinder to D a s h ...............................................
Master Cylinder to B o o ste r .........................................
Vacuum Booster to Dash ............................................
Push Rod to C levis...........................................................
Brake Line Nuts (to Master Cyl. and Valves) . . . .
Brake Line Nuts (to Front Brake H o s e )..................
Brake Line Nut (to Wheel Cylinder) .......................
Brake Line Nut (to Rear Brake Hose) .....................
Brake Hose (to Wheel C ylin d er)................................
Brake Line Clip to Frame ............................................
Front Brake Hose Support B ra ck et..........................
Rear Hose Frame or Axle B racket.............................
Brake Line Connector to A x l e ...................................
Brake Bleeder V a lv e s .....................................................
Brake Shoe Anchor P in ..................................................
Wheel Cylinder to Flange Plate ................................
Caliper Mounting Bolt ..................................................
Caliper Housing Bolt .....................................................
Flex Hose to Caliper Bolt ............................................
Support Plate to Steering Knuckle (Upper B o lt). .
Support Plate/Steering Arm to Knuckle Nuts . . .
Shield to Steering Knuckle Nuts (Hold Bolt) . . .
Shield to Steering Knuckle Bolt (Hold Nut) . . .
Pedal Mounting Pivot Bolt (Nut) .............................
Brade Pedal Bracket to D a s h ......................................
Combination Valve Mounting ...................................
Distribution Switch M o u n tin g ...................................
Parking Brake Equalizer ...............................................
Parking Brake Assembly (to Dash or Floor) . . . .
Parking Brake Assembly (to X.P-. or Kick Pad). . . .
Front Cable to Floor Pan ............................................
Front Cable Trans. Support B r a c k e t........................
Rear Cable Bracket ........................................................
TORQUE (FT. LBS.)
CORVETTE
Drive Spindle Support
to Torque A r m ............................................................. 30
Strut Rod
to Spindle Support......................................................75*
Bracket to Carrier.........................................................35
Camber C am ....................................................................... 65
Torque Arm P ivot............................................................. 50
Spring Link Bolt
to Torque Arm
Rear Wheel Alignment #

BRAKES

SECTION 5
TORQUE SPECIFICATIONS
Chevelle,
Chevrolet
and 125" W.B. Wagons
W.B. Wagons and Monte
24 ft. lbs.
18 ft. lbs.
24 ft. lbs.
18 ft. lbs.
24 ft. lbs.
18 ft. lbs.
150 in. lbs. 150 in. lbs. 150 in. lbs. 150 in. lbs. 150 in. lbs.
150 in. lbs. 150 in. lbs. 150 in. lbs. 120 in. lbs. 150 in. lbs.
150 in. lbs. 150 in. lbs. 150 in. lbs. 150 in. lbs.
150 in. lbs. 150 in. lbs. 150 in. lbs. 150 in. lbs. 115 in. lbs.
22 ft. lbs.
100 in. lbs. 100 in. lbs. 100 in. lbs. 100 in. lbs. 100 in. lbs.
100 in. lbs.
100 in. lbs. 100 in. lbs. 100 in. lbs.
100 in. lbs.
150 in. lbs. 20 ft. lbs. 100 in. lbs. 120 in. lbs.
65 in. lbs. 65 in. lbs.
120 ft. lbs. 120 ft. lbs.
50 in. lbs. 50 in. lbs.
35 ft. lbs. 35 ft. lbs.
22 ft. lbs.
22 ft. lbs.
140 in. lbs. 140 ft. lbs.
. 70 ft. lbs.
70 ft. lbs.
95 ft. lbs.
25 ft. lbs.
28 ft. lbs.
20 ft. lbs.
20 ft. lbs.
150 in. lbs.
150 in. lbs.
—
55 in. lbs.
55 in. lbs.
100 in. lbs.
in. lbs.
150
in. lbs.
150 8 5
—
72 in. lbs.
—
Install Nut to expose hole
then insert cotter pin.
116"
Camaro
Nova
Carlo
24 ft. lbs. 24 ft. lbs.
24 ft. lbs. 24 ft. lbs.
24 ft. lbs.
24 ft. lbs.
— —
14 ft. lbs.
22 ft. lbs.
—
100 in. lbs. 22 ft. lbs.
—
65 in. lbs. 65 in. lbs.
120 ft. lbs. 120 ft. lbs.
50 in. lbs. 50 in. lbs.
35 ft. lbs. 35 ft. lbs.
—
22 ft. lbs. 22 ft. lbs.
140 in. lbs. 140 ft. lbs.
—
70 ft. lbs.
— 70 ft. lbs.
—
95 ft. lbs.
28 ft. lbs.
—
150 in. lbs. 150 in. lbs.
— —
150 in. lbs. 100 in. lbs.
85 in. lbs.
85
in. lbs. 100 in. lbs. 100 in. lbs.
1 0 0
in. lbs. in. lbs. 85 in. lbs.
1 5 0
ft. lbs.
3 0
—
in. lbs.
1 0 0
4 0
Corvette
24 ft. lbs.
24 ft. lbs.
24 ft. lbs.
14 ft. lbs.
—
—
—
—
—
65 in. lbs.
—
—
70 ft. lbs.
130 ft. lbs.
—
22 ft. lbs.
—
—
—
—
— —
—
150 in. lbs.
—
70 in. lbs.
in. lbs.
—
— —
— —
ft. lbs. in. lbs.
1 0 0
OVERHAUL MANUAL