Page 3
All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. Revision User’s Manual for Wired / Wireless ADSL 2/2+ Router Model: ADE-3400v3 / ADE-4400v3 / ADW-4401v4 Rev: 2.0 (Nov. 2008) Part No. EM-ADE3400v3_v2...
1. Introduction The PLANET Wired / Wireless ADSL 2/2+ Router, the ADE-3400v3 / ADE-4400v3 / ADW-4401v4, provides office and residential users the ideal solution for sharing a High-Speed ADSL 2/2+ broadband Internet connection on the 10/100Mbps Fast Ethernet Interface and the 54Mbps wireless network. It can support downstream transmission rates up to 24Mbps and upstream transmission rates up to 3.5Mbps.
Page 8
Ethernet Port The ADE-3400v3 provides one Ethernet port, making it easy to create or extend your LAN. 4-Port Switch The ADE-4400v3 / ADW-4401v4 incorporates a 4-Port 10/100Base-TX switching hub, making it easy to create or extend your LAN. DHCP Server Support Dynamic Host Configuration Protocol provides a dynamic IP address to PCs and other devices upon request.
1.2 Package Contents ‧ ADE-3400v3 / ADE-4400v3 / ADW-4401v4 Unit x 1 ‧ Power Adapter x 1 ‧ Quick Installation Guide x 1 ‧ User’s Manual CD x 1 ‧ RJ-11 cable x 2 ‧ RJ-45 cable x 1 ‧ Splitter x 1 ‧...
Page 10
Front Panel LED definition State When the router is powered on and in ready state. The devise is being turned on and booting. When the router is powered off. Successful connection between ADSL modem and telecom's Link network. Flashing Modem is trying to establish a connection to telecom’s network. Data Flashing Data is transferred between Router and Internet.
Page 11
Front Panel of ADE-4400v3 Front Panel LED definition State Green Link Flashing Data Flashing LAN 1-4 Flashing Rear Panel Rear Panel Port and Button Definition Connector Description The power button is for turn on or turns off the router. POWER Button The reset button can restore the default settings of device.
Page 12
defaults, keep the device powered on and push a paper clip into the hole. Press down the button over 5 seconds and then release. Power Power connector with 12V DC 1.0 A Router is successfully connected to a device through the corresponding port Ethernet (1, 2, 3, or 4).
Page 13
Front Panel of ADW-4401v4 Front Panel LED definition State Green Link Flashing WLAN Flashing LAN 1-4 Flashing Rear Panel When the router is powered on and in ready state The devise is being turned on and booting When the router is powered off Successful connection between ADSL modem and telecom's network Modem is trying to establish a connection to telecom’s network...
Page 14
Rear Panel Port and Button Definition Connector Description POWER The power button is for turn on or turns off the router. Button The reset button can restore the default settings of device. To restore factory Reset defaults, keep the device powered on and push a paper clip into the hole. Press down the button over 5 seconds and then release.
2. Installation This chapter offers information about installing your router. If you are not familiar with the hardware or software parameters presented here, please consult your service provider for the values needed. 2.1 System Requirement Personal computer (PC) Pentium III 266 MHz processor or higher 128 MB RAM minimum 20 MB of free disk space minimum RJ45 Ethernet Port...
Figure 2 ADE-4400 / ADW-4401 connection diagram If do not need to connect to the splitter, Connect the modem to wall jack with a telephone cable. Use Ethernet cable to connect “LAN” port of the modem and network adaptor of your computer.
Page 17
3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
Page 18
Configuring PC in Windows 2000 Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. Double-click Local Area Connection. In the Local Area Connection Status window click Properties. Select Internet Protocol (TCP/IP) and click Properties. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons.
Page 19
Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3.
3. Web Configuration Management Determine your connection settings Before you configure the router, you need to know the connection information supplied by your ADSL service provider. Connecting the ADSL Router to your network Unlike a simple hub or switch, the setup of the ADSL Router consists of more than simply plugging everything together.
Once you have powered on ADE-3400v3 / ADE-4400v3 / ADW-4401v4, system will boot up and connect to DSLAM automatically. In login dialog, enter “admin” as user name and “admin” as default password. After log in, you will see the following page. The default screen is Wizard setting screen.
3.1.2 LAN Status You can see the LAN IP address, Mask, DHCP status, MAC and DHCP Client Table in this screen. 3.1.3 WLAN Status (ADW-4401 only) You can see the basic settings and status of wireless Interface in this screen. It includes the wireless band, mode, SSID and client list etc.
3.1.4 WAN Status You can see the VPI/VCI, Encapsulation type, Protocol, WAN IP address, Gateway and DNS information in this screen. 3.1.5 Port Mapping You can see the Port Mapping information in this screen. It includes the status and Mapping Relation.
3.1.6 Statistic You can see the Statistic information in this screen. It includes the Traffic and DSL statistic. Traffic Statistic Screen The screen shows the statistic of LAN, WLAN and WAN Port. Click the Refresh button to refresh the information. DSL Statistic The screen shows the ADSL line statistic.
3.2 Wizard You can use "Wizard" to setup the router as follows, and the router will connect to the Internet via ADSL line. Step 1. Click "Wizard" to get into the quick setup procedures. It will show the below screen. Enter the VPI / VCI value that provided by your ISP. Step 2.
Page 27
Step 3. Select the WAN IP type; select the WAN IP setting provided by your ISP. Step 4. Enter the user name and password that your ISP has provided to you. Select the connection type that you want to use. There are three types for your selection – Continuous, Connect on Demand and Manual.
Page 28
Step 5. Click "Next" to setup your LAN IP and DHCP Server setting. Step 6. Enter the Finish to save settings and reboot the device or click Back to modify your settings.
3.3 LAN The LAN setup includes two parts – LAN Interface and DHCP Settings. 3.3.1 LAN Interface Settings There are the IP settings of the LAN Interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is provided to your internal network and cannot be seen on the Internet.
3.3.2 DHCP Server Settings Enable the DHCP Server if you are using this device as a DHCP server. This page lists the IP address pools available to hosts on your LAN. The device distributes numbers in the pool to hosts on your network as they request Internet access. You can setup DHCP server to assign IP address to your PC automatically.
Page 31
Enter the MAC address and the IP address that you wish to assign in the fields. Click the “Assign IP” button to add it in the MAC-Base Assignment Table.
3.4 WLAN (For ADW-4401 only) Click “WLAN” and it will open out the Sub-Menu. It includes the “Basic Settings”, “Security”, “Advanced Settings”, “Access Control”, and “WDS”. 3.4.1 Basic Settings Go to WLAN Basic Settings to setup the wireless parameters. Function buttons in this page: Disable Wireless LAN Interface: Click it will disable your Wireless LAN Interface.
Send Rate: Select the Wireless Data Rate that you want to use. Radio Power: 10%, 25%, 50%, 80%, 100%. Note: Please Commit/Reboot if you want to make this settings effective immediately 3.4.2 Security This page allows you can configure security features of the wireless LAN interface. You can set the network authentication method, selecting data encryption, specify whether a network key is required to authenticate to this wireless network and specify the encryption strength.
Page 34
Following is a description of the different options: Key Length: Select 64-bit WEP or 128-bit WEP to use data encryption. Key Format: Select the ASCII or Hex format for encryption. Default Tx Key: Select Key 1 ~ 4 for your default Encryption Key. Network Key 1 to 4: Enter 5 ASCII characters or 10 hexadecimal digits for 64-bit encryption keys to fill out WEP keys box.
Pre-shared Key Format: Select the Passphrase or Hax format. Pre-shared Key: Enter the pre-shared key for WPA. Client stations must use the same key in order to connect with this device. Check the table below for instructions when entering the key. Radius Port: Enter the port number of the authentication server.
Beacon Interval: The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1024. A beacon is a packet broadcast by the Router to synchronize the wireless network. Note: Please Commit/Reboot if you want to make this settings effective immediately 3.4.4 Wireless Access Control You can allow or deny a lust of MAC addresses associated with the wireless stations access to the ADSL Router.
3.4.5 WDS (Wireless Distribution System) Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS.
3.5 WAN 3.5.1 WAN Interface ADSL 2/2+ Router provide 8 PVCs with different channel mode. You can select the Bridge / MER / PPPoE / PPPoA mode for your environment. Bridge Mode The device can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable 2 or more networks to communicate as if they are 2 segments of the same physical LAN.
Page 39
PPPoE / PPPoA Mode Select this option if your ISP requires you to use a PPPoE / PPPoA connection. This option is typically used for DSL service. Please enter the proper information in the fields. 1. Open the WEB page at “WAN 2.
Page 40
1. Open the WEB page at “WAN 2. Select the Channel Mode to “1483 MER”. Set the value of VPI / VCI and select the Encapsulation mode from your ISP. 3. Select the WAN IP type: DHCP or Fixed IP. 4.
3.5.2 ATM Settings The page is for ATM PVCs’ QoS mode setting. The device supports 4 QoS mode — UBR / CBR /rt-VBR / nrt-VBR. You can click the “ATM Setting” on the WAN Interface setting screen. ATM QoS: Select the Quality of Service types for this Virtual Circuit. The ATM QoS types include CBR(Constant Bit Rate), VBR(Variable Bit Rate) and UBR (Unspecified Bit Rate).
SCR: Sustained Cell Rate (SCR) is the mean cell rate of a bursty, on-off traffic source that can be sent at the peak rate, and a parameter for burst-type traffic. SCR may not be greater than the PCR; the system default is 0 cells/sec. MBS: Maximum Burst Size (MBS) is the maximum number of cells that can be sent at the PCR.
3.6 Advance You can configure different advanced services in this part. It includes DNS, Firewall, Virtual Server, Routing, IP QoS, Anti-DoS, Port Mapping and Other. 3.6.1 DNS In this screen, you can modify the DNS server settings. It includes the DNS and DDNS functions.
Page 44
DDNS In this screen, you can modify the Dynamic DNS settings. The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname in any of the many domains, allowing your DSL router to be more easily accessed from various locations on the Internet.
3.6.2 Firewall Firewall is an advance feature used to deny or allow traffic from passing through the device. ADSL router support some firewall related functions. It includes the IP/Port Filter, MAC Filter and URL Blocking. 3.6.2.1 IP/Port filtering Use the IP/Port filters to deny / allow particular LAN IP addresses from accessing the Internet.
Rule Action: Select the Deny or Allow for your rules. Direction: Select the Outgoing or Incoming. Protocol: Set protocol type to be blocked or allowed. Src IP Address / Mask / Port: Set the subnet of source side computers to be denied / allowed access to the destination side computers.
Page 47
Default Action: Specify default filtering rule action to be either Deny or Allow if no other rules can be applied. Click the “Apply Changes” to apply your setting. By default, all Outgoing and Incoming action is allowed. Click the “Add Rule” button to show filtering rule field, enter the rule information that you want to use.
3.6.2.3 URL Block This page is used to configure the Blocked FQDN (Such as tw.yahoo.com) and filtered keyword. Here you can add / delete FQDN and filtered keyword. URL Blocking: Enable or Disable URL Blocking. Click the “Apply Changes” to apply your setting.
3.6.3 Virtual Server The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. The Virtual Server includes two parts –...
3.6.3.2 DMZ A DMZ (Demilitarized Zone) allows a single computer on your LAN to expose ALL of its ports to the Internet. Enter the IP address of that computer as a DMZ (Demilitarized Zone) host with unrestricted Internet access. When doing this, the DMZ host is no longer behind the firewall.
3.6.4 Routing You have two ways to manage the device’s routing information. It includes RIP and Static Route. 3.6.4.1 RIP Enable the RIP if you are using this device as a RIP-enabled router to communicate with others using the Routing Information Protocol. This page is used to select the interfaces on your devices that use RIP, and the version of the protocol used.
3.6.4.2 Static Route This page is used to configure the routing information. Here you can add / delete IP routes. Click “Enable” to enable the Static Routing function, you can query the preset static routes, delete an existing static route, or add a new static route. By default, the system has no static route information.
3.6.5 IP QoS Entries in this table are used to assign the precedence for each incoming packet based on physical LAN port, TCP / UDP port number, and source / destination IP address / subnet masks. IP QoS: Enable or Disable IP QoS function. Click the “Apply Changes” to apply your setting.
3.6.6 Anti-DoS "denial-of-service attack" (DoS Attack), a type of attack on a network that is designed to bring the network to its knees by flooding it with useless traffic. This page is used to prevent DOS attacks that you configure. Select “Enable”...
3.6.7 Port Mapping Port Mapping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Delete button will remove the grouping and add the ungrouped interfaces to the Default group.
3.6.8 IPSec VPN (ADW-4401 only) The IPSec VPN (Virtual Private Network) feature in the ADW-4401v4 allows you to create a VPN connection between 2 ADW-4401v4. It is easy to configure and share the resource between two-sites through a secure and safe connection. IPSec VPN Configuration VPN: Enable or Disable IPSec VPN Connection Name: Each IPSec VPN is given a unique name to identify it.
Page 57
IPSec VPN Example In this example, 2 LANs are connected via IPSec VPN. Each end has an ADW-4401v4. Note • The LANs MUST use different IP address ranges. • Both endpoints have fixed WAN (Internet) IP addresses. IPSec Settings of ADW-4401 Site A: Step 1.
Page 58
IPSec Settings of ADW-4401 Site B: Step 1. Enable the VPN, it needs to take several minutes. Step 2. Enter a Name for this connection. Step 3. Enter the Local public IP as “61.62.236.12”. Step 4. Enter the Remote public IP as “203.73.50.242”. (ADW-4401-A WAN IP) Step 5.
3.6.9 PPTP (ADW-4401 only) ADW-4401v4 incorporates a PPTP (Peer-to-Peer Tunneling Protocol) server which is compatible with the "VPN Adapter" provided with recent versions of Microsoft Windows. Remote Windows clients are able to connect to this Server. Once connected, they can access the LAN as if they connected locally.
Page 60
Windows PPTP Client Setup To connect to the PPTP (VPN) Server in the VPN Broadband Gateway: • The Microsoft VPN feature in the VPN Broadband Gateway must be enabled and configured, as described in the previous section. • Each user must have a login (username and password) on the VPN client database on the VPN Broadband Gateway.
Page 61
5. Click "Finish" to exit the Wizard. The new entry will now be listed in "Dial-up Networking". If necessary, you can change the settings for this connection by right-clicking on it, and selecting Properties. To force all outgoing traffic to be sent via VPN, enable the setting, this is the default Internet connection on the Dialing tab.
Page 62
Windows 2000 Ensure you have logged on with Administrator rights before attempting this procedure. 1. Open "Network Connections", and start the "New Connection" Wizard. 2. Select the VPN option ("Connect to a private network through the Internet"), as shown below, and click Next. Windows 2000 Network Connection 3.
Page 63
4. On the screen below, enter the Domain Name or Internet IP address of ADW-4401v4 you wish to connect to. Click Next to continue. 5. Choose whether to allow this connection for everyone, or only for yourself, as required. Click Next to continue. Windows 2000 Connection Availability Windows 2000 VPN Host...
Page 64
6. Enter a suitable name, and click "Finish" to save and exit. Setup is now complete. To establish a connection: 1 Right-click the connection in "Network Connections", and select "Connect". 2 You will then be prompted for the username and password. Enter the username and password assigned to you, as recorded in the VPN client database on ADW-4401v4.
Page 65
Windows XP Ensure you have logged on with Administrator rights before attempting this procedure. 1. Open Network Connections (Start-Settings-Network Connections), and start the New Connection Wizard. 2. Select the option "Connect to the network at my workplace", as shown below, and click Next.
Page 66
4. Enter a suitable name for this connection. Click Next to continue. 5. On the screen below, select "Do not dial the initial connection". Click Next to continue. 6. On the screen below, enter the Domain Name or Internet IP address of ADW-4401v4 you wish to connect to.
Page 67
7. Choose whether to allow this connection for everyone, or only for yourself, as required. Click Next to continue. Windows XP Connection Availability 8. On the final screen, click Finish to save and exit. Setup is now complete. To establish a connection: 1 Right-click the connection in "Network Connections", and select "Connect".
3.6.10 Other This function includes as following parts – IGMP Proxy, UPnP and Bridge. 3.6.10.1 IGMP Proxy IGMP Proxy enables the system to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The system acts as a proxy for its hosts when you enable it by doing the follows: Enable IGMP proxy on WAN interface (upstream), which connects to a router running IGMP.
3.6.10.2 UPnP UPnP (Universal Plug and Play) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. An UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network.
3.6.10.3 Bridge This page is used to configure the bridge parameters. Here you can change the settings or view some information on the bridge and its attached ports. Aging Time: Enter the time for the bridge. 802.1d Spanning Tree: You can Enable or Disable the 802.1d Spanning Tree Protocol. Click “Apply Changes”...
3.7 Admin You can configure admin management in this part. It includes Remote Access, Commit / Reboot, Password, Backup / Restore, Update Firmware, Time Zone, System Log, SNMP TR-069 (For ADW-4401), and ACL. 3.7.1 Remote Access User can enable or disable remote management services for the LAN and WAN. Select the service items which you want to remote management.
3.7.2 Commit / Reboot The Comit / Reboot screen allows you to restart your router with its current settings or the factory default settings. If you want reset the current settings to factory default, please choose "reset to default settings", and then press "Reboot" to reboot system. If you want commit current settings, please choose "commit current settings", and then press "Reboot"...
3.7.3 Password This page is used to set the account to access the web server of ADSL Router.The new password will be availability after system reboot. User Name: There are two level user accounts for your selection. The admin account have full rights for device management, and the user account only can see the status information of this device.
3.7.4 Backup / Restore This page allows you to backup current settings to a file or restore the settings from the file which was saved previously. Backup: Click the “Save…” button to backup the configuration of router. Restore: Click the “Browsing...” button, select the correct update configure settings file. Then click the “Upload”...
3.7.5 Upgrade Firmware You can upgrade the firmware of the router in this page. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to browse the local had drive and locate the firmware to be used for the update.
3.7.6 Time Zone The system time is the time used by the device for scheduling services. You can manually set the time or connect to a NTP (Network Time Protocol) server. If an NTP server is set, you will only need to set the time zone. Time Mode: You can choose “Time Server”...
3.7.7 System Log Click “System Log” to show the log information of device. The system log dialog allows you to view the system log and click the “Refresh” button to fresh the system event logs. System Log: You can Enable or Disable the System Log Function. Click “Apply Changes”...
3.7.8 SNMP This page is used to configure the SNMP protocol. You can set SNMP related information here. Read Community: Select to set the password for incoming Get- and GetNext request from management station. Write Community: Select to set the password for incoming Set request from management station.
3.7.10 ACL Access Control List Configuration If enabled, permits access to local management services from IP addresses contained in the Access Control List. If enable ACL, and then only the effective IP in ACL can access the router. Step1 If you want to enable ACL, please choose "Enable" and then press "Apply Changes"...
3.8 Diagnostic Your router is capable of testing your network and DSL connection. The individual tests are listed as Ping, ATM Loopback, ADSL and Diagnostic. 3.8.1 Ping This page is used to send ICMP ECHO_REQUEST packets to network host. The diagnostic result will then be displayed.
3.8.3 ADSL In this page, you can test the ADSL line tone status. Click “Go” to start testing. The test result will come out about 3 minutes later and the page will refresh itself automatically. Note: This test is for ADSL 2 / 2+ Line only. 3.8.4 Diagnostic The DSL Router is capable of testing your DSL connection.
Page 83
Appendix A: Glossary Address mask A bit mask select bits from an Internet address for subnet addressing. The mask is 32 bits long and selects the network portion of the Internet address and one or more bits of the local portion. Sometimes it called subnet mask. AAL5 ATM Adaptation Layer - This layer maps higher layer user data into ATM cells, making the data suitable for transport through the ATM network.
Page 84
DHCP (Dynamic Host Configuration Protocol) DHCP is software that automatically assigns IP addresses to client stations logging onto a TCP/IP network. DHCP eliminates having to manually assign permanent IP addresses to every device on your network. DHCP software typically runs in servers and is also found in network devices such as Routers.
Page 85
Hop count A measure of distance between two points on the Internet. It is equivalent to the number of gateways that separate the source and destination. HTML Hypertext Markup Language - The page-coding language for the World Wide Web. HTML browser A browser used to traverse the Internet, such as Netscape or Microsoft Internet Explorer.
Page 86
Management Information Base - A collection of objects can be accessed via a network management protocol, such as SNMP and CMIP (Common Management Information Protocol). Network Address Translation - A proposal for IP address reuse, where the local IP address is mapped to a globally unique address.
Page 87
Route The path that network traffic takes from its source to its destination. The route a datagram may follow can include many gateways and many physical networks. In the Internet, each datagram is routed separately. Router A system is responsible for making decisions about which of several paths network (or Internet) traffic will follow.
Page 88
Spoofing A method of fooling network end stations into believing that keep alive signals have come from and returned to the host. Polls are received and returned locally at either end Static IP Address A static IP address is an IP address permanently assigned to computer in a TCP/IP network. Static IP addresses are usually assigned to networked devices that are consistently accessed by multiple users, such as Server PCs, or printers.
Page 89
independent requests, such as requesting a MIB value from an SNMP agent, in which first setting up a connection would take more time than sending the data. UNI signaling User Network Interface signaling for ATM communications. Virtual Connection (VC) A link that seems and behaves like a dedicated point-to-point line or a system that delivers packets in sequence, as happens on an actual point-to-point network.
Important Note According to Annex3 of the ERC/REC 70-03 publication, the use of Wideband Data Transmission systems has the following National Restrictions: Frequency range: 2400-2483.5MHz Country Restriction France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Italy Luxembourg None...
For the following equipment: *Type of Product ADSL 2/2+ Router *Model Number : ADE-3400A / ADE-3400B * Produced by: Manufacturer‘s Name Manufacturer‘s Address is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to For the evaluation regarding the R&TTE the following standards were applied: Emission Harmonic...
Page 92
For the following equipment: *Type of Product ADSL 2/2+ 4-Port Router *Model Number : ADE-4400A / ADE-4400B * Produced by: Manufacturer‘s Name Manufacturer‘s Address is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to For the evaluation regarding the R&TTE the following standards were applied: Emission...
Page 93
For the following equipment: *Type of Product : 802.11g Wireless ADSL 2/2+ Router *Model Number : ADW-4401A / ADW-4401B * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 9F, No. 96, Min Chuan Road, Hsin Tien Taipei, Taiwan, R. O.C. is herewith confirmed to comply with the requirements set out Approximation of the Laws of the Member States relating to 1999/5/EC R&TTE.