Video - Pioneer VSX-AX5Ai-G Operating Instructions Manual

12 Additional information
Symptom
When playing a DTS format LD
there is audible noise on the
soundtrack.
Can't record audio.
Subwoofer output is very low.
Everything seems to be set up
correctly, but the playback sound
is odd.
Noise or hum can be heard even
when there is no sound being
input.
There seems to be a time lag
between the speakers and the
output of the subwoofer.

Video

Symptom
No image is output when an
input is selected.
The System Setup screen
doesn't appear.
98
En
Cause
• The input signal type is set to ANALOG.
• You are trying to make an analog recording
from a digital signal, or a digital recording of
an analog source.
• The digital source is copy protected.
• The analog REC jacks have not been
connected properly.
• The bass attenuator is set too low.
• The speaker settings result in very little
audio signal being sent to the subwoofer.
• The speakers are out of phase.
• There is electrical interference from another
component or appliance.
• The subwoofer channel can be delayed
slightly if run through a low-pass filter.
Cause
• The video connections are incorrect.
• You are using component video
connections for your source, but not for your
TV.
• You are using component video
connections and the component video inputs
are assigned incorrectly.
• The DVD/video player settings are incorrect. • Set correctly. Refer to the instruction manual supplied
• The video input selected on the TV monitor
is incorrect.
• Even though the sub room monitor is
connected properly, the multi-room feature is
switched off.
• The component video inputs are assigned
to a video component connected only to the
composite or S-Video terminals.
• The MONITOR OUT jack hasn't been
connected.
• You connected your TV to the MULTI ROOM
& SOURCE MONITOR OUT jack instead of
the main MONITOR OUT jack.
• Some TVs connected to the receiver with
component video cables do not display the
System Setup screen when the Color Burst
feature is on (this applies to the NTSC video
system format only).
Remedy
• Set the input signal type to DIGITAL (see Selecting the
input signal type on page 43)
•You can only record analog to analog, or digital to digital.
• You can't record digital sources that have been copy
protected.
• Check your analog connections (see Connecting analog
audio sources on page 26).
• See Bass Peak Level on page 93 to adjust the setting.
• Change your subwoofer setting to one of the following in
the Speaker Setting on page 55:
Front: SMALL / Subwoofer: YES
Front: LARGE / Subwoofer: PLUS
• Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding
terminals on the speakers (page 28).
• Check that personal computers or other digital
components connected to the same power source are not
causing interference.
• See Automatically setting up for surround sound on
page 12 to set up your system again using MCACC (this
will automatically compensate for a delay in the
subwoofer output).
Remedy
• Make sure the video component is connected correctly
(see pages 19–27).
• Using the video converter, video signals can be
converted from a composite or S-video input to a
component video output, but not vice-versa. See About the
video converter on page 16 for more on this.
• Check Assigning the component video inputs on page 82
to make sure you're assigned the correct input.
with the DVD/video player.
• Set correctly. Refer to the instruction manual supplied
with the TV.
• Press the MULTI ROOM&SOURCE ON/OFF button to
switch it on.
• Check Assigning the component video inputs on page 82
to make sure the component video assign for that video
component is switched to OFF.
• Connect the MONITOR OUT jack to the TV monitor (see
Connecting your TV on page 18).
• When the receiver is in standby, switch to COLOR
BURST OFF by holding down the MULTI JOG CONTROL
RETURN button and pressing
current setting appears in the display).
STANDBY/ON. (the