Programming Signals From Other Remote Controls - Pioneer VSX-AX5Ai-G Operating Instructions Manual

Controlling other equipment
8 Repeat steps 3 – 7 for any other components you
want to control.
9 When you're finished, use
to select '*Exit*' from the menu and press ENTER.
Programming signals from other
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
assigning a preset code in Recalling preset codes on
page 58.
VCR1 /
DVD/LD TV/SAT TV CONT
DVR
MULTI CONTROL
VCR2 VIDEO CD
CD-R/ MD/
TAPE1 TAPE2
1 Press and hold REMOTE SETUP for three seconds.
The REMOTE SETUP menu appears on the remote
control display.
2 Use (cursor up/down) to select 'Learning'
from the menu and press ENTER.
Select Function flashes in the display.
3 Press the MULTI CONTROL button that matches
the connection for the component you want to
control.
For example, press DVD/LD if you want to program an
operation for the DVD player that you connected to the
DVD/LD terminals.
Select Key flashes in the display.
• You can't assign the RECEIVER or TUNER buttons.
4 Select the button corresponding to the command
you want to teach the remote control.
For example, press if you want to program the play
command from your DVD player remote control.
LEARN flashes in the display.
• When programming TV CONT, you can only select
TV , or one of the TV CONTROL buttons.
5
other then press the corresponding button on the
other remote control that is sending (teaching) the
(cursor up/down)
signal to this receiver's remote control.
For example, if you want to learn the playback control
signal, press
• The remote controls should be 5–20cm apart, and the
If the operation has been learned, the display will show OK
If the operation hasn't been learned the display will show
NG.
Continue? shows in the display (if Select Key is flashing,
go back to step 4). Go to step 6.
ENTER
• If the remote display shows FULL, it means the
• If NG keeps showing in the display, or the remote
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons avail-
REMOTE
SETUP
able are shown below:
6
program additional signals for the current compo-
nent.
Repeat steps 4 and 5.
• To program signals for another component, select
7
to select '*Exit*' from the menu and press ENTER.
You will return to the REMOTE SETUP menu. Select
*Exit* again to exit.
Point the two remote controls towards each
.
LEARN icon should be flashing to indicate the
remote is ready to accept a signal.
5 – 20cm
memory is full. See Clearing remote control settings
on page 69 to erase a programmed button you're not
using to free up more memory.
control keeps on returning to step 4 (Select Key
flashes in the display), it may be possible that the
command cannot be learned by this remote control.
SOURCE TV
Use (cursor up/down) to select 'Yes' to
No and repeat steps 2 through 5.
When you're finished, use
DIMMER LOUDNESS TONE EFFECT/CH SEL
1 2 3 4
+
SIGNAL SEL DNR BASS/TREBLE
5 6 7 8
+10
VIDEO SEL HI-BIT
DISC
9 0
ENTER
DIRECT ACCESS SEARCH MODE
SYSTEM SETUP GUIDE
MENU TOP MENU
TUNER EDIT TRACK
ENTER
EXIT
AUDIO RETURN
MPX
TEXT ON RF ATT DISP MODE
SUB TITLE
+
TUNING BAND TUNING
+
STATION TEXT OFF CLASS STATION
+
CHANNEL CHANNEL
(cursor up/down)
08
59
En