Programming Signals From Other Remote Controls; Erasing One Of The Remote Control Button Settings - Pioneer SC-LX73 Operating Instructions Manual

10 Controlling the rest of your system (In case of SC-LX83)
Programming signals from other
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
assigning a preset code.
1 While pressing MULTI OPERATION, press HOME
MENU.
The remote display shows SETUP MENU.
Use / to select 'CODE LEARNING', then press
2
ENTER.
The remote display prompts you for the component you
want to control (for example DVD or TV).
3 Press the input function button for the component
you want to control, then press ENTER.
PRESS KEY blinks in the remote display.
4 Point the two remote controls towards each other,
then press the button that will be doing the learning on
this receiver's remote control.
PRESS KEY lights continuously to indicate the remote is
ready to accept a signal.
• The remote controls should be 3 cm apart.
5 Press the corresponding button on the other
remote control that is sending (teaching) the signal to
this receiver's remote control.
For example, if you want to learn the playback control
signal, press and hold  briefly. The remote display will
shows OK if the operation has been learned.
If for some reasons the operation hasn't been learned the
remote display will shows ERROR briefly, and then
display PRESS KEY again. If this happens, keep pressing
the (teaching) button as you vary the distance between
the two remotes, until the remote display shows OK.
Note
1 The remote can store about 200 preset codes (this has been tested with codes of Pioneer format only).
2 • You can't assign TUNER, HMG NET RADIO, ADAPTER and iPod USB.
• The TV CONTROL buttons (TV, TV VOL +/–, TV CH +/–, MUTE and INPUT) can only be learned after the operation selection switch is set
to TV.
3 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
4 • Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or
farther apart.
• If the remote display shows MEMORY FULL, it means the memory is full. See Erasing one of the remote control button settings on page 80
to erase a programmed button you're not using to free up more memory (note that some signals may take more memory than others).
• Depending on the type of command that has been learned, operation may not be possible with RF two-way communications. In this case,
operate using IR signal transmission. For instructions on switching between the IR and RF modes, see Operating other components by RF
communications on page 87.
80
En
1
2
3 cm
3
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons
available are shown below:
MAIN
RECEIVER
ZONE2
BDR
BD DVD DVR
NET RADIO
TV CD HMG
USB
iPod TUNER
MULTI CH
PHONO IN VIDEO
INPUT SELECT
AUX
SOURCE
TV
CH VOL
TV CONTROL
INPUT MUTE
AUDIO
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
7 Press and hold MULTI OPERATION for a couple of
seconds to exit and store the operation(s).
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing MULTI OPERATION, press HOME
MENU.
The remote display shows SETUP MENU.
Use / to select 'ERASE LEARNING', then press
2
ENTER.
4
The remote display prompts you for the component
corresponding to the button setting to be erased.
TV CONTROL
INPUT MUTE
SOURCE
AUDIO
3 PARAMETER PARAMETER
TUNE
TOOLS
LIST
MULTI
OPERATION
TOP MENU
BAND
HDMI
PRESET
ENTER
ADAPTER
OPTION CATEGORY
1 2
HOME
MENU
TUNE
iPod CTRL PTY SEARCH
CD-R STATUS PHASE CTRL CH LEVEL
LIGHT
THX MPX PQLS MEMORY
AUTO/ALC/
STANDARD ADV SURR
DIRECT STEREO
PGM MENU
SIGNAL SEL SLEEP DIMMER AUDIO
A.ATT SBch MCACC INFO
DISP
HDMI OUT
RECEIVER
CH
D.ACCESS CLASS
ENTER
VOL
CLR
MUTE
VIDEO
MUTE
VIDEO
T.EDIT
GUIDE
PRESET
RETURN